Related Manuals for Briggs & Stratton 1695776
Summary of Contents for Briggs & Stratton 1695776
- Page 1 ATTACHMENT OPERATOR’S MANUAL Triple Catcher 1695776 Triple Catcher for 46” and 52” Regent and NXT Mowers Copyright © Briggs & Stratton Corporation 1750622 Milwaukee, WI, USA. All rights reserved. Rev.: B...
-
Page 3: Table Of Contents
Table of Contents Operator Safety ..............General Warnings ................. Safety Decals ..................Assembly................Mower Mounting Hardware Installation ..........Baffle Installation .................. Hitch and Frame Installation ..............Tube Assembly ..................Attach Collector Bags ................Operation................Collector Installation ................Operation ....................Collector Removal ................. -
Page 4: Operator Safety
Operator Safety Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. -
Page 5: Assembly
Assembly Free Floating Mowers Before beginning any service work turn WARNING: 1. From the inside of deck, near front of discharge opening off the PTO, set the parking brake, turn off the ignition, assemble 1.25” carriage bolt (A, Figure 3), .341” OD x and disconnect the spark plug wire(s). -
Page 6: Baffle Installation
Assembly Baffle Installation For 52” Mower Decks 1. Lift side discharge chute (A, Figure 5). For 46” Mower Decks 2. Insert longest baffle (B) through discharge opening and 1. Lift side discharge chute (A, Figure 4). position baffle inside deck. 2. -
Page 7: Hitch And Frame Installation
Assembly Hitch and Frame Assembly 5. Install the bag and cover support (A, Figure 8) to upright support (B) using four 3/8-16 x .875 bolts (C) and four 1. Slide the 5/16-18 speed nut (A, Figure 6) onto rear frame 3/8-16 whiz locknuts (D) as shown. -
Page 8: Tube Assembly
Assembly Tube Assembly Frame Hung Mowers 1. Rotate latch (A Figure 12) into pocket of hardware 1. Ensure latch hardware is in the correct hole for the deck assembly (B). sizes as shown in Figure 10. Note: Remove and re-assemling hardware may be required. - Page 9 Assembly Free Floating Mowers 3. Slide the upper and middle tube (E, Figure 17) into cover (F) aligning ridge (G) with cutout (H) as shown. 1. Rotate latch (A, Figure 14) into pocket of hardware assembly (B). Figure 14 2. Secure hook (C, Figure 15) of mounting strap (D) onto roller bar support bracket (E).
-
Page 10: Attach Collector Bags
Assembly Attach Collector Bags 1. Raise the cover (A, Figure 19). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). Note: It may be necessary to fold seat forward to allow cover to stay in the raised position. Figure 19... -
Page 11: Operation
Operation Collector Installation 1. Mount the hitch and frame assembly (A, Figure 20) onto rear tractor frame. 2. Slide the upper tube (B) into cover (C) aligning ridge (D) with cutout (E) as shown. 3. Raise the cover. 4. Attach collector bags (F) using grass bag hanger (G) to bag hanger post. -
Page 12: Operation
Operation Before Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. -
Page 13: Collector Removal
Operation Collector Removal : Operation Without Bagger CAUTION For operation without bagger, the mower deflector MUST be properly installed in the down position and retained by the spring latch. 1. Lift up cover (A, Figure 16), then remove and empty bags (B). -
Page 14: Warranty
Warranty BRIGGS & STRATTON PRODUCTS WARRANTY POLICY LIMITED WARRANTY Briggs & Stratton warrants that, during the warranty period specified below, it will repair or replace, free of charge, any part that is defective in material or workman- ship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is effective for and is subject to the time periods and conditions stated below.