Table of Contents
Advertisement
Quick Links
USER MANUAL
Transceiver Module
TCM 300 / TCM 300C
TCM 320 / TCM 320C
June 14, 2011
Patent protected:
WO98/36395, DE 100 25 561, DE 101 50 128,
WO 2004/051591, DE 103 01 678 A1, DE 10309334,
WO 04/109236, WO 05/096482, WO 02/095707,
US 6,747,573, US 7,019,241
EnOcean GmbH
Kolpingring 18a
82041 Oberhaching
Germany
Downloaded from
Elcodis.com
electronic components distributor
V1.25
Observe precautions! Electrostatic sensitive devices!
Phone +49.89.67 34 689-0
Fax
+49.89.67 34 689-50
info@enocean.com
www.enocean.com
Subject to modifications
TCM 300 / 300C / 320 / 320C User Manual V1.25
June 14, 2011 4:53 PM
Page 1/52
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for EnOcean TCM 300
Summary of Contents for EnOcean TCM 300
- Page 1 US 6,747,573, US 7,019,241 EnOcean GmbH Phone +49.89.67 34 689-0 Subject to modifications Kolpingring 18a +49.89.67 34 689-50 TCM 300 / 300C / 320 / 320C User Manual V1.25 82041 Oberhaching info@enocean.com June 14, 2011 4:53 PM Germany www.enocean.com Page 1/52 Downloaded from Elcodis.com...
- Page 2 This information describes the type of component and shall not be considered as assured characteris- tics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the EnOcean web- site: http://www.enocean.com.
-
Page 3: Table Of Contents
3.7.2 TCM 320 / TCM 320C ................35 3.8 Tape & Reel specification TCM 300 / TCM 300C ..........35 © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 3/52 Downloaded from Elcodis.com... - Page 4 A.3.4 SW Version ..................... 46 A.3.5 Error messages ..................47 A.3.6 Command Encoding ................. 48 © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 4/52 Downloaded from Elcodis.com electronic components distributor...
-
Page 5: General Description
Transmit mode: typ. 24 mA, max. 33 mA (TX) @ 0.1% telegram error rate (based on 3 transmitted sub-telegrams) © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 5/52 Downloaded from Elcodis.com... -
Page 6: Physical Dimensions
PCB outline dimensions ±0.2 mm All other tolerances ±0.1 mm TCM 320 / TCM 320C © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 6/52 Downloaded from Elcodis.com electronic components distributor... -
Page 7: Environmental Conditions
TCM 320 S3003-K320 868.3 MHz TCM 300C S3033-K300 315.0 MHz TCM 320C S3033-K320 315.0 MHz © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 7/52 Downloaded from Elcodis.com electronic components distributor... -
Page 8: Functional Description
PROG_EN RVDD The figure above shows the pin out of the TCM 300 / TCM 320 hardware. The pins are named according to the naming of the EO3000I chip to simplify usage of the DOLPHIN API. The table in section 2.2 shows the translation of hardware pins to a naming that fits the functionality of the built-in firmware. -
Page 9: Pin Description And Operational Characteristics
ADIO6 MODE 0-1: SER_RX UART input MODE 2-4: not used Digital input, internal pull-up active © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 9/52 Downloaded from Elcodis.com electronic components distributor... - Page 10 Normal operation: Learn mode indicator Remote Management: ACTION command indi- cator (see 2.9.1) Digital output © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 10/52 Downloaded from Elcodis.com electronic components distributor...
-
Page 11: Gpio Supply Voltage - Iovdd
For I/O pins configured as analog pins the IOVDD voltage level is not relevant! However it is important to connect IOVDD to a supply voltage as specified in 2.4. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 11/52 Downloaded from Elcodis.com... -
Page 12: Absolute Maximum Ratings (Non Operating)
WXIDIO / WXODIO VIND2 Voltage at WXIDIO / WXODIO input pin VDDR Max. ripple at VDD mVpp © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 12/52 Downloaded from Elcodis.com electronic components distributor... -
Page 13: Operating Modes
Each rocker is counted as 1 entry. If the same rocker is teached into several channels, 1 entry per channel is needed. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 13/52 Downloaded from Elcodis.com... -
Page 14: Mode Selection
36% to 39.99% VDD R1: 5k6 ±1% R2: 10k ±1% R3: 56k ±1% C1: 100p © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 14/52 Downloaded from Elcodis.com electronic components distributor... -
Page 15: Repeater Configuration
TCM 300 / 300C / 320 / 320C Repeater configuration TCM 3x0 provides the option to activate a one or two-level repeater for EnOcean radio tele- grams. 1-level repeater: If a received telegram is a valid and original (not yet repeated), the tele- gram is repeated after a random delay. -
Page 16: Teach-In Procedure
4 seconds with active LRN bit it will be deleted again. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 16/52 Downloaded from Elcodis.com... -
Page 17: Confirmation Of Correct Learning/Deletion
All learned transmitters on all channels are deleted at the same time. After this, the re- ceiver enters Learning Mode. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 17/52 Downloaded from Elcodis.com... -
Page 18: Remote Management
3 transmissions within 2 seconds are required, instead of 1 transmission For detailed information on remote management please refer to the Remote Management system specification. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 18/52 Downloaded from Elcodis.com electronic components distributor... -
Page 19: Smart Acknowledge
2.10 Smart Acknowledge TCM 3x0 provides a post master function with 15 mail boxes for systems using EnOcean smart acknowledge technology. This functionality is switched on in all operating modes. For detailed information on smart acknowledge please refer to the Smart Acknowledge sys- tem specification. -
Page 20: Applications Information
A summarized application note to determine the transmission range within buildings is available as download from www.enocean.com. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 20/52 Downloaded from Elcodis.com electronic components distributor... -
Page 21: Antenna Options Tcm 300 / Tcm 300C
For 315 MHz modules (STM 300C and TCM 3X0C) please note that a full approval is needed if modules are used with antennas other than the specified whip antenna. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 21/52 Downloaded from Elcodis.com... -
Page 22: Whip Antenna
Minimum distance space: 10 mm Specification of the whip antenna; L=150 mm @ 315 MHz, L=86 mm @ 868 MHz © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 22/52 Downloaded from Elcodis.com... -
Page 23: Chip Antenna
AMD1103-ST01 GND plane RF_50 Minimum distance space above and below PCB: 11 mm © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 23/52 Downloaded from Elcodis.com electronic components distributor... - Page 24 AMD1103-ST01 GND plane RF_50 Minimum distance space above and below PCB: 11 mm © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 24/52 Downloaded from Elcodis.com electronic components distributor...
-
Page 25: Splatch Antenna
3.5.3. Distance space for components RF_50 Minimum distance space above and below PCB: 12 mm © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 25/52 Downloaded from Elcodis.com electronic components distributor... -
Page 26: Helical Antenna
RF_50 ANT-315-HE GND plane Minimum distance above and below axis of antenna: 21 mm © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 26/52 Downloaded from Elcodis.com electronic components distributor... -
Page 27: Antenna Options Tcm 320 / 320C
Isolation material may brake at temperatures below -15 °C. Please take care to fix the antenna cable in case vibrations are expected. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 27/52 Downloaded from Elcodis.com... -
Page 28: Mounting 50 Ω Antennas
16-pin connector! It is recommended to use a strain relief for that purpose. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 28/52 Downloaded from Elcodis.com electronic components distributor... -
Page 29: Recommendations For Laying A Whip Antenna
GND area Antenna end led back to foot point Antenna too close to GND area © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 29/52 Downloaded from Elcodis.com electronic components distributor... -
Page 30: Power Supply Requirements
The RVDD line should be kept as short as possible. Please consider recommenda- tions in section 3.10. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 30/52 Downloaded from Elcodis.com electronic components distributor... -
Page 31: Tcm 300/300C Recommended Foot Pattern
TCM 300 / 300C / 320 / 320C 3.6.1 TCM 300/300C recommended foot pattern Top layer © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 31/52 Downloaded from Elcodis.com electronic components distributor... - Page 32 USER MANUAL V1.25 TCM 300 / 300C / 320 / 320C Solder resist top layer © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 32/52 Downloaded from Elcodis.com electronic components distributor...
- Page 33 Nevertheless an application and production specific test regarding the amount of soldering paste should be performed to find optimum parameters. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 33/52 Downloaded from Elcodis.com...
-
Page 34: Soldering Information
TCM 300 has to be soldered according to IPC/JEDEC J-STD-020C standard. TCM 300 shall be handled according to Moisture Sensitivity Level MSL4 which means a floor time of 72 h. TCM 300 may be soldered only once, since one time is already consumed at production of the module itself. -
Page 35: Tcm 320 / Tcm 320C
Tape & Reel specification TCM 300 / TCM 300C Tape running direction © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 35/52 Downloaded from Elcodis.com electronic components distributor... -
Page 36: Backward Compatibility To Tcm 220C
EN60669-2-1). As soon as the supply voltage drops below the VON threshold level the current consumption is reduced. TCM 300 will enter standby sleep mode (worst case 35 µA), TCM 320 will enter short term sleep mode (1.8 mA) for 200 ms. As long as the voltage at VDD does not drop below VOFF during that phase the module will restore the output state as set before the voltage dip. -
Page 37: Agency Certifications
External antenna at RF_50 Antenna type Passive Impedance ~50 Ohm Maximum gain ≤ 0 dBi © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 37/52 Downloaded from Elcodis.com electronic components distributor... -
Page 38: Fcc (United States) Certification
TCM 300C FCC ID:SZV-STM300C IC:5713A-STM300C STM 300C FCC ID:SZV-STM300C IC:5713A-STM300C TCM 320C FCC ID:SZV-TCM320C IC:5713A-TCM320C © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 38/52 Downloaded from Elcodis.com electronic components distributor... - Page 39 TCM 300 / 300C / 320 / 320C OEM Requirements In order to use EnOcean’s FCC ID number, the OEM must ensure that the following condi- tions are met: End users of products, which contain the module, must not have the ability to alter the firmware that governs the operation of the module.
- Page 40 The OEM must ensure that timing requirements according to 47 CFR 15.231(a-c) are met. The OEM must sign the OEM Limited Modular Approval Agreement with EnOcean © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 40/52 Downloaded from Elcodis.com electronic components distributor...
-
Page 41: Ic (Industry Canada) Certification
TCM 300 / 300C / 320 / 320C IC (Industry Canada) Certification In order to use EnOcean’s IC number, the OEM must ensure that the following conditions are met: Labeling requirements for Industry Canada are similar to those required by the FCC. - Page 42 USER MANUAL V1.25 TCM 300 / 300C / 320 / 320C © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 42/52 Downloaded from Elcodis.com electronic components distributor...
-
Page 43: A Serial Interface
(binary 1) Byte HIGH D7 STOP Time Time Time Signals and bit order sending a byte © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 43/52 Downloaded from Elcodis.com electronic components distributor... -
Page 44: Description Of Serial Data Structure
(RID) is stored together with the ID.) This module allows using a unique ID or one of 128 IDs starting from BaseID. See A.3.1. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 44/52 Downloaded from Elcodis.com... -
Page 45: Radio Transmission/Reception Commands
Alliance pursues standardization of communication profiles, ensuring that sensors from one manufacturer can communicate with receiver gateways of another, for example. End-users thus have the entire product portfolio - enabled by EnOcean - at their disposal. And product manufacturers can focus on their own special field. -
Page 46: Command Telegrams And Messages
A.3.1 ID Range commands Every TCM 300 supports a unique 32 bit ID and in addition a range of 128 IDs starting at an BaseID address. At production, every TCM 300 is programmed with a unique ID and a BaseID address. -
Page 47: Error Messages
TCM 300 / 300C / 320 / 320C A.3.5 Error messages Error Messages (RCT) ERR_TX_IDRANGE ERR_IDRANGE ERR_SYNTAX © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 47/52 Downloaded from Elcodis.com electronic components distributor... -
Page 48: Command Encoding
10 times is exceeded or an ERR_IDRANGE telegram if the BaseID is not within the allowed range. © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 48/52 Downloaded from Elcodis.com... - Page 49 An OK confirmation telegram is generated after TCM sen- sitivity has been changed. Sensitivity=0x00 Low sensitivity Sensitivity=0x01 High sensitivity ChkSum © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 49/52 Downloaded from Elcodis.com electronic components distributor...
- Page 50 Bit 7 Bit 0 Performs a reset of the TCM microcontroller. 0xA5 0x5A 0xAB 0x0A ChkSum © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 50/52 Downloaded from Elcodis.com electronic components distributor...
- Page 51 Errors can occur in the H_SEQ, LENGTH, ORG or CHKSUM Field fields/bytes. Field code: H_SEQ=0x08 ORG=0x0B LENGTH=0x09 CHKSUM=0x0A ChkSum © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 51/52 Downloaded from Elcodis.com electronic components distributor...
- Page 52 SET_BASEID command to a value outside 0x8B the allowed range from 0xFF80_0000 to 0xFFFF_FFFE. 0x1A ChkSum © 2010 EnOcean | www.enocean.com TCM 300 / 300C / 320 / 320C User Manual V1.25 | Page 52/52 Downloaded from Elcodis.com electronic components distributor...
Need help?
Do you have a question about the TCM 300 and is the answer not in the manual?
Questions and answers