ProMinent Vario d Operating Instructions Manual

ProMinent Vario d Operating Instructions Manual

Metering pump

Advertisement

Operating instructions
Metering pump
Vario d, VAMd
EN
Target group: trained, qualified personnel, unless otherwise required.
Please carefully read these operating instructions before use. · Do not discard.
The operator shall be liable for any damage caused by installation or operating errors.
The latest version of the operating instructions are available on our homepage.
Part no. 999719
Original operating instructions (2006/42/EC)
Version: BA VA 024 11/21 EN

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vario d and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ProMinent Vario d

  • Page 1 Operating instructions Metering pump Vario d, VAMd Target group: trained, qualified personnel, unless otherwise required. Please carefully read these operating instructions before use. · Do not discard. The operator shall be liable for any damage caused by installation or operating errors.
  • Page 2 Supplemental directives General non-discriminatory approach In order to make it easier to read, this document uses the male form in grammatical structures but with an implied neutral sense. The document is always aimed equally at women, men and gender-neutral persons. We kindly ask readers for their understanding in this simplification of the text.
  • Page 3: Table Of Contents

    4.5 Sound pressure level............13 4.6 Supplementary information for modified design....13 Dimensional drawings..............14 Diagrams for adjusting the dosing rate.......... 15 Wear parts for Vario d, VAMd............16 7.1 Spare parts kits..............16 7.2 Diaphragms................17 Declaration of Conformity for Machinery........18...
  • Page 4: Product Identification Vario D, Vamd

    Product identification Vario d, VAMd Product identification Vario d, VAMd Tab. 2: design with motor: 3-phase, 400 V, 50 Hz Order no. Nominal pressure * Nominal pump capacity * 1118827 1118828 1118829 1118830 1118831 * refer to nameplate for precise back pressure and pump capacity.
  • Page 5: Safety Chapter

    Only start up the pump once it has been correctly installed and started up in accordance with the technical data and specifications contained in the operating instructions. Observe the general limitations with regard to viscosity limits, chem‐ ical resistance and density - see also ProMinent resistance list in the ® www.prominent.com ! product catalogue or at All other uses or modifications are prohibited.
  • Page 6 Safety chapter DANGER! Nature and source of the danger Consequence: Fatal or very serious injuries. Measure to be taken to avoid this danger. Description of hazard – Denotes an immediate threatening danger. If the sit‐ uation is disregarded, it will result in fatal or very serious injuries.
  • Page 7: Users' Qualifications

    Trained user A trained user is a person who fulfils the requirements made of an instructed person and who has also received additional training specific to the system from ProMinent or another authorised distribution partner. Trained qualified personnel...
  • Page 8: Safety Information

    An unsuitable feed chemical can damage the parts of the pump that come into contact with the chemical. – Take into account the resistance of the wetted mate‐ rials and the ProMinent Resistance List when selecting the feed chemical - see the ProMinent Product Catalogue or visit ProMinent.
  • Page 9: Isolating Protective Equipment

    Safety chapter 2.5 Isolating protective equipment All isolating protective equipment must be installed for operation: Power end front cover Motor fan cowling Motor terminal box cover Plug Information in the event of an emergency In the event of an electrical accident, disconnect the mains cable from the mains or press the emergency cut-off switch fitted on the side of the system! If feed chemical escapes, also depressurise the hydraulic system around...
  • Page 10: Repair

    – Take into account the resistance of the wetted mate‐ rials and the ProMinent Resistance List when selecting the feed chemical - see the ProMinent Product Catalogue or visit ProMinent. P_VA_0005_SW Fig. 1: Liquid end parts...
  • Page 11 Repair Put in place protective measures, if necessary. Adhere to the material safety data sheet for the feed chemical. Ensure that the system is at atmospheric pressure. Drain the liquid end. Turn the liquid end upside down and allow the feed chemical to drain out.
  • Page 12: Technical Data

    Technical data Technical data Only with "M - modified" design: Please observe the ”Supplementary information for modified design“ at the end of the chapter. The supplementary information replaces and supplements the technical data. 4.1 Performance data The dosing rate for 50 Hz at maximum back pressure can be found on the nameplate of the pump housing.
  • Page 13: Ambient Conditions

    Technical data 4.4 Ambient conditions 4.4.1 Ambient temperatures Pump, complete Data Value Unit Storage and transport temperature: -10 ... +50 °C Ambient temperature in operation (pump -10 ... +40 °C part): Ambient temperature in operation (con‐ -10 ... +50 °C trol): 4.4.2 Media temperatures Material version...
  • Page 14: Dimensional Drawings

    Compare the dimensions on the dimension sheet – and pump. All dimensions are in mm. – Dimensional drawing of Vario d Fig. 2: Dimensional drawing of Vario d Tab. 5: Dimensions of Vario d Material version 042 PVT G3/4A-DN10 246 (251*)
  • Page 15: Diagrams For Adjusting The Dosing Rate

    Diagrams for adjusting the dosing rate Diagrams for adjusting the dosing rate Vario (FM 042) VAMd VAMd 12042 04120 VAMd 12026 VAMd VAMd 07063 12017 VAMd 12042 p [bar] s [%] Vario (FM 063) Vario (FM 120) VAMd VAMd 07063 04120 VAMd VAMd...
  • Page 16: Wear Parts For Vario D, Vamd

    Wear parts for Vario d, VAMd Wear parts for Vario d, VAMd The spare parts kit generally includes the wear parts for the liquid ends. 7.1 Spare parts kits Scope of delivery of PVT: 1 metering diaphragm 1 suction valve assembly...
  • Page 17: Diaphragms

    Wear parts for Vario d, VAMd 7.2 Diaphragms Tab. 9: Diaphragms for ... Liquid end Order no. FM 042, types 12017, 12026, 12042 811458 FM 063, types 10025, 09039, 07063 811459 FM 120, types 06047, 05075, 04120 811460...
  • Page 18: Declaration Of Conformity For Machinery

    In accordance with the Machinery Directive 2006/42/EC Tab. 10: Extract from the Declaration of Conformity Certificate number: IN-DL-5805-20033M Licensee: ProMinent Fluid Controls (Dalian) Co., Ltd. Address: No. 14 Road Liaohexisan Dalian Economic & Technical Development Zone, P. R. China Manufacturer: ProMinent Fluid Controls (Dalian) Co., Ltd.
  • Page 20 ProMinent GmbH Im Schuhmachergewann 5 - 11 69123 Heidelberg Germany Telephone: +49 6221 842-0 Fax: +49 6221 842-419 Email: info@prominent.com Internet: www.prominent.com 999719, 1, en_GB © 2021...

This manual is also suitable for:

Vamd

Table of Contents

Save PDF