Page 3
safety precautions and usage statements safety precautions and usage statements Attention: Important Safety Disclaimers Read all instructions before using your adjustable base. Save these instructions. WARNING WARNING • Keep bed in a flat position when not in use. Always unplug the base from the electrical outlet before servicing any •...
safety precautions and usage statements WARNING audible as the wheels make contact. This is normal. For optimal safety and operation, plug bed base into a surge protector (not included). MATERIALS The bed base should only be plugged directly into a grounded wall outlet or surge Ergomotion adjustable bases are constructed from various materials including woods, protector (strongly recommended).
Page 5
safety precautions and usage statements Any adjustable foundation deemed to be within these allocated tolerances is with a clean cloth dampened with warm water to remove residues. Dry in shade away considered to have met the manufacturer’s quality control standards. from direct heat.
Page 6
safety precautions and usage statements DON’T: FCC Compliance: • Sit on corners/edges of base (this may warp the frame, struts or foam). NOTE: This equipment has been tested and found to comply with the limits • Tilt the base on its side (this can damage the legs and/or leg screws). for a Class B digital device, pursuant to part 15 of the FCC Rules.
parts list Before discarding the packing materials, ensure all the parts are accounted for. All electronics and components that need to be installed are located in boxes under the base or attached to the frame. Wireless Remote Control and AAA Batteries (3) Mattress Retainer Bar* Legs (4) and Leg Washers (4) Power Cord...
quick reference guide ELECTRONICS OVERVIEW Single Head Massage Motor Wireless Remote Control Box Head Motor Input Cord Power Cord Power Supply Foot Motor If installing a split unit, see pages 12-13...
installation guide Always use two people when setting up the base, moving or flipping the base. STEP 4 STEP 1 Place the bed base box in a desired location with the bottom of the box To sync two bases with the sync cord - see page 13 facing up.
Page 11
installation guide STEP 7 STEP 9 Carefully flip the base over onto its legs. Ensure batteries are correctly installed in the back of Important: Always use two people when setting up, moving or flipping the the remote. base. Do not drag across the floor. Do not rest frame on its side, excessive Quickly test functions to verify proper setup before pressure may damage the legs.
battery backup strap (optional) For emergency use only, in case of a power outage. Batteries are not to be used for normal operation of the bed. STEP 1 STEP 3 Disconnect the Power Supply from the input power cord. Connect the end of the Battery Backup Strap to the input power cord that is attached to the control box.
pair remote The original remote that comes in the box is already paired to the adjustable base. No further action is required. In the event that the remote is not paired with the base, follow the steps below. STEP 1 STEP 3 Unplug the Power Cord from your power outlet.
connecting strap (optional) If any split setup is being installed (excluding Divided King), plastic connecting straps are provided (one per base) to secure the bases together. Use both straps to secure the head and foot portions together. STEP 1 STEP 2 With the bases in their desired location, slightly loosen both legs to Slide side (a) of the connecting strap onto leg bolt.
A Sync Cord is included with the base. Not available on Queen, Full or Full-Long size bases. This process is most commonly used for syncing two connected TXL bases. STEP 1 Unplug bases from power source. Sync Cord STEP 2 Control Box 1 STEP 3 Plug bases back into the power source.
headboard bracket installation guide (optional) Headboard Brackets are an optional accessory and are not included. A 9/16” & 1/2” socket and crescent wrench are necessary to complete installation. STEP 1 c . Secure T-Bracket in place by inserting two short screws through Attach the Headboard Bracket.
troubleshooting If one or more functions on the bed base have stopped operating: • Check under the bed base to verify that the wired connections are secure and that there are no cords or bedding obstructing the movement of the base. •...
español Pg. 1 -4 - Precauciones y Declaraciones de Uso Corte de energía: use la “Caja de respaldo de batería de emergencia” como una fuente de energía Atención: Importantes Exenciones de Seguridad temporal para llevar la base a la posición deseada. Las instrucciones sobre cómo operar la caja de Lea todas las instrucciones antes de utilizar su base ajustable.
Page 19
español IMITES DE USO Todas las bases ajustables Ergomotions, dependiendo de su marca y modelo, están diseñadas y fabricadas para realizar y funcionar dentro de parámetros control de calidad establecidos. Las bases Los motores no están diseñados para funcionar continuamente por más de dos (2) minutos en un están sujetas a meticulosas y rigurosas inspecciones durante el proceso de control de calidad para periodo de dieciocho (18) minutos o aproximadamente 10% de un ciclo de trabajo.
Page 20
español Power LED Light = Luz LED de potencia Radiofrecuencia: 2.4 GHz Input Cord Connection = Entrada para Cable de Poder Pg. 5 - Lista de Partes Foot Motor Port = Entrada Motor Para Pies Antes de descartar los materiales de empaque, verifique que tiene todos los componentes. Head Motor Port = Entrada Motor Cabeza Todas las partes electrónicas y los componentes que necesitan instalarse están en cajas debajo de la base o adheridos al marco.
Page 21
español Pg. 10 - Correa de Baterías de Reserva Pg. 12 - Correa Conectora (opcional) Coloque la Caja Para Baterías de Reserva en un lugar accesible debajo de la cama para usos de Si se está instalando una configuración dividida (excluyendo el King Dividido), se proporcionas correas emergencia de conexión de plástico (una por base) para asegurar las dos bases.
Page 22
español français • Compruebe que la luz de la caja de control está encendida. Si no, verifique que los cables estén Pg. 1-4 - Consignes de sécurité et instructions d’utilisation correctamente conectados. • Desconecta la base durante 1 hora para restablecer los componentes electrónicos. ATTENTION •...
français Les roues, qui permettent au lit de maintenir sa distance du mur, entreront en contact avec le ATTENTION support d’acier de la plate-forme créant un bruit au contact. Ce bruit de contact peut être audible alors que les roues font contact lors du coucher, du lever, ou lorsque vous déplacez votre poids sur la base Ceci est normal.
Page 24
français émettre des sons dans des environnements plus froids. • Se tenir debout ou sautez sur la base réglable à tout moment (cela peut endommager le châssis et moteur). FONCTIONNEMENT JUMELÉ Il peut y avoir un temps de latence jusqu’à 5 secondes entre chaque articulation des bases lors de •...
Page 25
français Pg. 9 - Guide d’installation Position à plat Position Zéro-G® ÉTAPE 7: Tournez soigneusement la base sur ses jambes. Important : Toujours faire appel à deux personnes lors de l’installation ou lorsque vous tournez la base Ne pas glisser sur le plancher. Ne Pg.
Page 26
français Pg. 12 - Sangle de raccordement (facultatif) • Vérifier sous la base de lit pour vérifier que les connexions filaires sont sécurisées et qu’il n’y a Si n’importe quel arrangement divisé est en cours d’installation (à l’exclusion du King divisée), pas de cordons ou de la literie qui entrave le mouvement de la base.
Need help?
Do you have a question about the Motion Essentials V King and is the answer not in the manual?
Questions and answers