Serta 49347 Assembly Instructions Manual
  1. Manuals
  2. Brands
  3. Serta Manuals
  4. Indoor Furnishing
  5. 49347
  6. Assembly instructions manual

Serta 49347 Assembly Instructions Manual

Hide thumbs

Advertisement

Table of Contents

Executive Chair
Assembly Instructions
Model 49347

Advertisement

Table of Contents
loading

Related Manuals for Serta 49347

Summary of Contents for Serta 49347

  • Page 1 Executive Chair Assembly Instructions Model 49347...
  • Page 2 PARTS Casters Star Base Gas Lift with Telescoping Cover Seat Plate Quantity: 5 Quantity:1 Quantity: 1 Quantity: 1 Right Arm Left Arm Seat Cushion Back Cushion Quantity:1 Quantity: 1 Quantity: 1 Quantity: 1 1” Screws 1-1/2” Screws 1-1/4” Screws 1-1/2” Screws with Quantity: 2 Quantity: 2 Quantity: 4...
  • Page 3 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
  • Page 4 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-1/2” Screws (I) for the front holes of the Seat Plate (D) and 1” Screws (H) for the rear holes of the Seat Plate (D) and tighten screws.
  • Page 5 Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F). Push down the key on the receivers to pull out the levers. *Note: Fix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion.
  • Page 6 Step 5 Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with1-1/4” Screws (J). *Note: Do not tighten the screws completely. Step 6 Insert 1-1/2" Screws with Spring Washers (K) into arm holes attaching Arms (E1 &...
  • Page 7 Step 7 Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D).
  • Page 8 Step 8 Place the Arm Inserts (L1& L2, M1 & M2) into arm grooves once all screws have b een tightened.

  • Page 9: Operating Instructions

    Operating Instructions Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height.
  • Page 10 Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position.
  • Page 11 Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user.
  • Page 12 Attention: 1. Do not stand on the seat cushion. 2. For indoor use only. 3. Please do not expose to direct sunlight. 4. Please do not place this product near sources of excessive heat. 5. Please avoid use of sharp objects on or near this product. 6.

  • Page 13: Limited Warranty

    Limited Warranty Huali Trading seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases Huali Trading furniture from an authorized Huali Trading retailer as shown by the original sales receipt.

Table of Contents