Table of Contents
Advertisement
Invalid system configuration data
Keyboard controller error
Keyboard error
Keyboard error nn
Mouse initialized
Operating system not found
Parity check 1 nnnn
Parity check 2 nnnn
Press <F1> to resume, <F2> to
Setup
Press <Del> to enter SETUP
Previous boot incomplete - Default
configuration used
Real time clock error
Resource allocation conflict on
motherboard
Shadow RAM failed at offset: nnnn
System battery is dead - Replace
and run SETUP
System BIOS shadowed
System cache error - cache
disabled
System CMOS checksum bad - run
SETUP
System RAM failed at offset: nnnn
System timer error
The system configuration information in the
system setup program is incorrect, or the
battery charge may be low.
The keyboard controller failed its test.
The keyboard is not working correctly.
The BIOS has detected a stuck key
represented by scan code nn.
The system's mouse has been found and
initialized.
The operating system cannot be located on
drive A or drive C.
A parity error has been detected on the system
bus. The BIOS attempts to locate the address
and display it (nnnn); if it cannot locate the
address, it displays ???? instead.
A parity error has been detected on the I/O bus.
The BIOS attempts to locate the address and
display it (nnnn); if it cannot locate the address,
it displays ???? instead.
This message is displayed after any
recoverable error message.
Optional message displayed during POST.
After an unsuccessful boot, POST loads default
values and offers to run the system setup
program. (POST does not input these default
values to the system setup program.)
The RTC has failed the BIOS test.
The system cannot configure all system board
devices without a resource conflict.
Shadow RAM has failed at offset nnnn in the
64-KB block in which the error was detected.
The CMOS clock battery indicator shows the
battery is dead.
The system BIOS has been copied to shadow
RAM.
RAM cache failed the BIOS test; the BIOS has
disabled the cache.
System CMOS has been corrupted or modified
incorrectly, perhaps by an application program
that changes data stored in CMOS.
System RAM failed at offset nnnn in the 64-KB
block in which the error was detected.
The timer test failed.
Enter the
system setup program
system configuration; then restart the system.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
The keyboard or
system board
replaced.
Make sure nothing is resting on the keyboard; if
a key appears to be stuck, carefully pry it up. If
the problem persists, you may need to replace
the keyboard.
No action is necessary.
Enter the
system setup program
that drive A or drive C is properly identified.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
Press <F1> to start the boot routine or <F2> to
enter the
system setup program
any settings.
If desired, press <Del> to enter the
setup
program.
There may be incorrect values or incorrect
settings in the
system setup
program. Run the
system setup program and attempt to restore
the incorrect setting(s). If the message
reappears, set the
configuration jumper
Maintenance mode and restart the system to
return all settings to their defaults.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
Run the
system setup program
resolve any obvious resource conflicts. If the
message reappears, set the
configuration
jumper
to Maintenance mode and restart the
system to return all settings to their defaults.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
Replace the battery and run the
program
to reconfigure the system.
No action is necessary.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
Run the
system setup program
the system by either reverting to the default
values or by making your own selections.
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
If you receive this message after making
changes in the
system setup
program, enter the
program and restore the original value(s).
and verify the
may need to be
and confirm
and change
system
to
and try to
system setup
and reconfigure
Advertisement
Table of Contents
