Felton TATE Installation Manual
Digital wall mounted mixer
Hide thumbs
Also See for TATE:
- Installation manual (20 pages) ,
- User manual (12 pages) ,
- Installation manual (24 pages)
Related Manuals for Felton TATE
Summary of Contents for Felton TATE
- Page 1 INSTALLATION GUIDE TAT E Digital Wall Mounted Mixer TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 2 FELTON...
-
Page 3: Table Of Contents
CONTENTS Notice Tools Required Measurements Scope of Application Control Unit Installation Digital Mixer Installation Wall Mounted Spout Installation Operational Test Troubleshooting Warranty TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE... -
Page 4: Notice
Installation must be carried out by qualified installers in accordance to this installation manual. AS/NZS3500 standards, rules and safety regulations do apply. PLACE OF INSTALLATION The Tate Digital Controller must be installed in an accessible place and in accordance to this installation manual. This ensures a problem-free service and maintenance procedure. DANGER OF ELECTRIC SHOCK! ELECTRICAL INSTALLATION Before opening the housing, the mains connection must be switched off. Work on electrical parts and connections must be... - Page 5 4. Cable Tie BOX 3 WALL MOUNTED SPOUT 0-ring Seal 1 x Key Spout Base Sleeve 1 x Flow Straightener Spout Side View View Grub Screw x2 3 x Aerators/Flow Regulators (1x is prefitted to the spout) Aerator/Flow Regulator Side View View TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 6 IF YOU ARE INSTALLING AS A BASIN / SINK MIXER Install product as supplied. There additional flow regulators supplied in FLOW REGULATORS the box. Once the product is installed and has Pink Flow Regulator 4l/min been checked for leaks, you can test the Blue Flow Regulator 6l/min different flow regulators to see which one is White Flow Regulator 8l/min (factory fitted) the best option for your situation. IF YOU ARE INSTALLING AS A BATH MIXER Remove flow regulator from the spout and replace with a flow straightener (full flow). FELTON...
-
Page 7: Measurements
Power supply Warning: Please ensure that all electrical installations are installed by a registered electrician and complies with the Electrical (Safety) Regulations of NZ. Important: The Digital Mixer must have an access panel. TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE... -
Page 8: Control Unit Installation
Unit need to be positioned accordingly within this distance. It is recommended that the Data Cable is installed in conduit for ease of maintenance. The Control Tube can be reduced in length if required by cutting along the cutting slot (see Fig. 2). FELTON... - Page 9 Using the Data Cable, thread the end with the small connector through the hole and Control Mounting Tube. This end of the cable is protected with a plastic sleeve, leave this on until later in the installation. Foam Seal Control Housing CLICK Push the Control Mounting Apply a silicone bead on the Tube into the hole until the back of the Control Housing, front flange sits against the then push the Control Housing wall. into the Plastic Tube until it is firmly fitted on the unit. TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 10 This tightens the lugs on the inside of the wall. Tighten until there is no rotation of the Control Housing. Pull the red strip to release the connector from the plastic sleeve. Control Wheel Push the four pin connector into the socket on the back of the Control Wheel. Data Cable FELTON...
- Page 11 Thread in the cable and fit the Control Wheel onto the Housing. Fit the Control Sleeve onto the Control Wheel. SIDE VIEW Ensure that you fit the Control Sleeve in the correct orientation. TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
-
Page 12: Digital Mixer Installation
DIGITAL MIXER INSTALLATION Remove the cover Inside the Temperature Control Unit Control unit Fixing holes Transformer 12V / wall plug Cover retaining holes Fixing hole Cold Outlet Inlets FELTON... - Page 13 Mark fixing holes shown MOUNTING FOR CONCRETE 56 m m 56 m m 99 m m ø 5 m m 99 m m If installed vertically, use orientation shown Install the Drill fixing holes Digital Mixer Mark fixing holes TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 14 11. Connect the two Inlet hoses with the MF adaptors and filters to the water supply feed Large retaining bolt Hot inlet Cold inlet A - Connect the brass adaptors into the flexi hoses. B - Fit both flexi hoses (with the brass adaptor on) firmly into the unit box. C - Fit the large retaining bolt with a torx screw driver supplied. FELTON...
- Page 15 DIGITAL MIXER INSTALLATION Fit the outlet pipe on to the brass connectors Outlet pipe Push the outlet fitting into the Digital Mixer and fit a small retaining bolt with torx screw driver supplied Short retaining bolt TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 16 Connect the Data Cable coming from the Control Unit. Use the large 6 pin connector and push firmly into the socket. Feed the cable through the one of the guide slots in the front of the Digital Mixer. Data Cable connection Connect the power cable coming from the transformer. Use the connector and push firmly into the socket. Feed the cable through the guide slot in the front of the Digital Mixer. Power cable connection FELTON...
- Page 17 Fit the cover back on to the base. Using a Phillips screwdriver secure the cover in position. The unit is now ready for commissioning. Please see User Guide. IMPORTANT: Fit cables into slots to allow cover to properly close at end of installation TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
-
Page 18: Wall Mounted Spout Installation
Fit the spout onto the base, ensuring the sleeve stays on the spout and Fit Spout secure both grub screws using a 2.5mm allen key (not supplied). Fit Sleeve 4B. Fit the cover sleeve. Connect spout to digital mixer. Turn on the water supply, operate the mixer and check for leaks. FELTON... -
Page 19: Operational Test
OPERATIONAL TEST 1 Ensure that the Digital Mixer is installed correctly installed according to the instructions above. Turn on the water supply and check the unit and plumbing for leaks. Once the plumbing is confirmed to be water-tight, connect the power supply and conduct the operational test below. OPERATING THE CONTROL SYSTEM 1 Open Close Push the interface once. The interface turns on and the Push the interface again. The interface turns off and the LED illuminates. LED goes off. TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE... -
Page 20: Troubleshooting
The interface is defective in User Guide The knob is not running smoothly Remove and clean knob *Important: Controlling the flow rate is only possible with the Smartflow Digital Shower Mixer. If issue persists or is not covered in the above, please contact our Felton Technical Team on 0800 743 358 or sales@felton.co.nz FELTON... -
Page 21: Warranty
This warranty is for manufacturing defects only and does not cover any damage to product due to abuse, negligence or improper installation. This warranty is given on the understanding that the product is installed by a registered plumber and operated according to Felton’s installation guide and the Australian/New Zealand standard AS/NZS3500. This warranty is provided to persons who are a “consumer” under the Consumer Guarantees Act 1993 only and for use in domestic/residential dwellings only (not for commercial use). - Page 22 FELTON...
- Page 23 TATE DIGITAL WALL MOUNTED MIXER INSTALLATION GUIDE...
- Page 24 . c o . n z | F i n d u s o n S o c i a l M e d i a @feltontapware /feltonltd /FeltonIndustriesLimited @feltonltd /felton-industries-limited 090322EI FELTON...