Table of Contents
Advertisement
OPTIONS AND ACCESSORIES
For TOTAL TIG
system,
select
one
each of the
following
items:
Welding
power
source
TIG torch
TIG
kit
(see
hG
kits listed
below)
Coolant
system
(it using
water
cooled
torch)
Remote control
Note: The other items necessary
to
weld
are
power
source
primary
cable.
shielding
gas,
and filler metal.
KIT FOR MT17
and MTL17
SERIES AIRCOOLED
TORCHES
121/2
ft.
(3.8 m) length
(#129 590)
25 ft.
(7.6 m)
length
(#129
589)
Kit includes:
Hose & hardware
hookup
kit
(TH K-2)
Consumable accessory kit
(TAK1)
one
backcap
and
three
sizes
(.040,
1/16,
and
3/32
in.)
of
collets,
collet
bodies,
cups,
and 2% thoriated
tungsten
Regulator/flowmeter
(HRF2425)
Ground cable
with
clamp.
121/2
ft.
(3.8 m)
or
25 ft.
(7.6 m) lengths
to
match
TIG
torch
length
Note: Power cable
adapter
105Z57
(#116 276)
must
be ordered for torches
with
onepiece composite
cable.
POWER CABLE ADAPTERS
(Required
on
torches with
one-piece.
high-flex
cable
assembly
and all
water-cooled
torches.)
Adapter
105Z57
Stock No.
(#116 276)
INTERNATIONAL TIG TORCH
CONNECTOR
KIT
For direct connection of
onepiece
torches
or
watercooled
TIG
torches into power
sources
with
Internationalstyle
connectors.
FUSE BLOCK ASSEMBLY
For
use
with watercooled
torches. Five fuse links included
Up
to 260
Amps
(#116 163)
260
to 550
Amps
(#116164)
Protects torch from
overheating
and
damage
if water is
not
circulating
or
if torch is
run
considerably higher
than its rated
capacity.
Note: Additional fuse links available in
packages
of 5
(#116 559).
CABLE EXTENSION BOX
For
use
with watercooled
torches
CEB
(Nonfused)
(#120 797)
CEB 260FA
(#116 161)
(Fused
up to 260
Amps)
CEB 550FA
(#116 162)
(260
to
550
Amps)
Allows hose and cable
assembly
to
be extended from the power
source.
Available with
or
without
fuse
protection.
All
components
are
protected by
a
strong,
nonconductive
enclosure.
Note: Hose and cables from power
source
to
CEB box
are
not
supplied.
Use
large
diameter extension hoses and
heavy welding
cable for
optimum
performance.
RMCH14
and RLCH14
CONTACTOR SWITCHES
Torch handle
with
a
builtin
switch
for
remote contactor
control of
Miller solidstate TIG power
sources.
Includes 25 ft.
(7.6 m)
control cord with
14pin plug.
RMCH14S
(Momentary)
(#129 336)
RLCH14S
(Locking)
(#129 335)
TIG HOSE HOOK-UP KITS
(THK)
THK1
(Watercooled)
(#128 065)
THK2
(Aircooled)
(#128 066)
Provides
the
necessary hoses and
hardware
to connect
either
air
or
watercooled
torches
to
a
power
source
and,
if
applicable,
water
coolant
system.
GAS REGULATORS
With 580
CGA
inlet
connector
HRF2425
(#127 661)
This
regulator/flowmeter
has outlet
pressure
preset
at
25
PSIG;
the
maximum inlet is 3000
PSIG
and
has 540
SCFH gas
delivery.
AF1
50
(#127 662)
This
flowgauge regulator
has
adjustable
gas
delivery
of 825
SCFH with argon gas.
TIG ACCESSORY KITS
(TAK)
Kits include
one
backcap
and three
each of the
following:
collet,
collet
body,
alumina cup, and 2%
thoriated
tungsten pieces.
TAK1
(#129 585)
0.40, 1/16,
and
3/32
in. for MT17
TIG TORCH CABLE
COVERS
Reinforced
plastic
cable
covers
made of
tear
and
flame
resistant
material.
A
large
and small
cover
is
available in
length
to
fit
121/2
ft.
and 25 ft.
(3.8
and 7.6
m)
torches.
CC12S
(#126 150)
For
121/2
ft.
(3.8 m)
torches. Fits
Miller
TIG Torch models
80
Amps
through
250
Amps.
CC25S
(#126 151)
For 25 ft.
(7.6 m)
torches. Fits
Miller
TIG Torch
models 80
Amps
through
250
Amps.
REMOTE
CONTROLS
AMTV REMOTE
CONTACTOR
AND
CURRENT CONTROL
(#152 608)
Linear motion control fastens
to
hG
torch handle
using
two Velcro
straps.
The AMTV is
a
practical
alternative
to
a
foot control.
Includes 28 ft.
(8.5
m)
control cord
with
14pin
plug.
RCC REMOTE
CONTACTOR
AND
CURRENT CONTROL
RCC14
(14pin
plug)
(#151 086)
RCC5
(5pin plug)
(#157 365)
Rotary
motion
fingertip
control
fastens
to
TIG torch
using
two
Velcro
straps.
Includes 28 ft.
(8.5
m)
control cord.
1192
80
Amp
Torch
150
Amp
Torch
200
Amp
Torch
250/350
Amp
Torch
(#135 492)
(#135 493)
(#135 494)
(#135
495)
Advertisement
Table of Contents
