Troubleshooting - Rain Bird ST8I-INTL Manual Operation

GB English
Programming at the timer
Auto Auto is the normal operating mode
Press the AUTO key to return to normal
operation. During watering, the display shows
a blinking sprinkler symbol, the active ZONE
number and watering RUN TIME remaining
for that zone.
Rain Delay — Up to 14 Days Press and hold
the + button. The number of days along with
the stop icon will be displayed.
• Press + or – to increase or decrease the rain delay.
• After rain delay has elapsed, watering will automatically resume.
Date/Time Set current date and time
• Press the DATE/TIME key.
• Press + or – to adjust the current selection.
• Press NEXT (or BACK) to select the value you
wish to change.
Zone Schedule Create irrigation schedules
Press the zone SCHEDULE key, then follow steps 1 through 4.
1 Select Zone: Press + or – to select
desired ZONE number; then press NEXT.
2 Set Watering Run Time: Press
+ or – to set desired RUN TIME ;
then press NEXT.
3 Set Watering Start Times: Press + or –
to set first START TIME; then press NEXT.
REPEAT as desired to set additional START TIMES for that zone.
NOTE: Pressing NEXT with -:- (OFF) is blinking on the display will
advance to Step 4.
NOTE: Watering START TIMES automatically stack.
Set Watering Start Days: Press + or – to select one of four available
4
options:
4-a Custom Days
• Press + or – to select then press NEXT.
• Press ON (to enable) or OFF (to disable) the blinking SELECTION DAY.
Cursor will then advance to the next SELECTION DAY.
REPEAT for each day of the week as desired.
4-b Odd Days
Press + or - to select
4-c Even Days
Press + or – to select
4-d Cyclic Days
• Press + or – to select
• Press + or – to set desired DAY CYCLE; then press NEXT.
• Press + or – to set desired START DATE; then press NEXT.
REPEAT steps 1–4 for additional zones as desired.
Manual Watering Start watering immediately
• Press the MANUAL watering key.
• Press + or – to select ALL zones or any
SINGLE zone; then press NEXT.
• Press + or – to set desired RUN TIME; then
press NEXT to begin watering.
NOTE: Only stations with programmed RUN
TIMES and START TIMES will water manually.
NOTE: To stop manual watering, press the OFF key to stop irrigation and
then press the AUTO key to return to normal operation.
NOTE: If ALL zones are watering, pressing NEXT will advance watering
to next zone.
Seasonal Adjust Increase or decrease watering duration (Run Times)
for all Zones.
• Press the SEASONAL ADJUST button
• Press + or – to increase or decrease the SEASONAL ADJUST percentage
setting.
NOTE: The SEASONAL ADJUST value can be adjusted from -90% to
+100%. For example, a +50% adjustment means a Run Time of 10
minutes will become 15 minutes.
NOTE: If "Use Weather Correction Data"
is enabled in the app, then adjusting the
seasonal adjust at the timer will only make
a change for the day. The adjustment will
change back to the seasonal adjust setting
controlled by the app the next day.
183943-01,09JL20,MANUAL,ST8I-INTL,ManualOperation.indd 4
MIN
4
1
2
then press NEXT.
then press NEXT.
then press NEXT.
THEN
MIN
Setting
NOTE: SEASONAL ADJUST applies to ALL programmed irrigation
schedules.
Press AUTO to resume normal operation.
Rain Sensor Bypass
Set controller to OBEY or IGNORE a Rain Sensor.
Set Bypass for One Zone
• Press the SCHEDULE key.
• Press + or – to select the desired Zone number.
• Press and release both BACK and NEXT keys at the same time to toggle
between OBEY and IGNORE.
SYMBOL is displayed when IGNORE is selected.
Set Bypass for All Zones
• Press the AUTO key.
• Press and release both BACK and NEXT keys at the
same time to toggle between OBEY and IGNORE.
SYMBOL is displayed when IGNORE is selected.

Troubleshooting

Display Error Cause
Err Break or loose wire to
Master Valve if used.
3
Blank No power
Frozen
Possible electrical
surge
WiFi Module
Cause
Blinking
Green Timer not connected
to mobile device
Red and Green Mobile device not
detecting timer wifi
signal
Red WiFi module needs to
be reset
Not blinking
No power
Watering Issues Cause
No watering Water supply problem Check main and supply water lines.
Loose wires
Corroded or damaged
wires
Rain sensor may be
activated
Jumper wire missing
or damaged
Solution
Replace wiring. Press NEXT.
Verify supply wires are connected.
Unplug for 2 minutes. Press RESET.
Solution
Reconnect using App.
Connect using App Setup Wizard.
Press WiFi module button until LED blinks
red and green. Follow the app Setup
Wizard to reset.
Check AC outlet and seating of the
module in port.
Solution
Check wires at timer, valve and master
valve.
Replace if needed
Let sensor dry out or disconnect it and
add jumper wire to SENS terminals.
Replace if needed
7/9/20 11:33 AM
FR
Pr