Advertisement
Quick Links
Advertisement
Related Manuals for Radio Shack 2770422
Summary of Contents for Radio Shack 2770422
- Page 1 S t a r t i n g w i t h DIY Drone Starter Kit 2770422 User’s Guide...
- Page 2 We hope you enjoy your DIY Drone Starter Kit from RadioShack. This kit comes with everything you need to build and fly a Quad-Rotor Drone. Please read this user’s guide before using your new kit. Package Contents Check you have all the components before you start. 3.7V 250mAH Lithium Polymer Battery Top Body Cover...
- Page 3 USB Charging Cable Remote Control Required Tools • Soldering Iron • Lead-free Solder • Diagonal Cutter Notes: This kit contains electronic components that may contain hazardous substance and may be harmful if misused. This activity is not intended for children under the age of 12. Not to be used by children except under adult supervision.
- Page 4 Solder LEDs LEDs are polarized and MUST Red/Red LED1 match the position printed LED1 (1) on the PCB. The longer pin is positive and the shorter pin is White/ LED2 negative. Green LED2 (4) Insert leads into the correct pads, bend the LEDs so they extend from the board as indicated below, solder, then trim leads.
- Page 5 Solder Motor Wires Connect Battery Turn on the PCB to Motor 1 (2) Motor 2 (2) White 3.7V 250mAH Lithium test LED connections. Polymer Battery (1) Black Black ON/OFF Motor 1 Motor 2 Motor 2 Motor 1...
- Page 6 Assemble Body Top Body Cover Bottom Body Cover 1.2 x 4mm Screws Observe direction! Insert motor wires Keep wires away from into slots connecting posts CHG Port Fit holes into posts Fit holes ON/OFF into posts Switch Widen LED leads around posts carefully using a pair of pliers...
- Page 8 Propellers A (2) 1.2 x 4mm Screws (8) Propellers B (2) Suspension Pads (4) The left and right propellers are different (see A and B markings on the drone and propellers). Make sure you insert the correct propeller in the correct location to fly properly.
- Page 9 Charge the Drone Battery 1. Make sure your drone is switched off. Plug the USB charging cable into your drone’s charging port (CHG) and a USB power source. The LED on the USB connector lights red during charging, and turns off when charging is complete.
- Page 10 Install Batteries in the Remote Control Set the remote control’s ON/OFF switch to OFF. Open the battery compartment and insert two AAA batteries (not included), matching the polarities (+ and –) marked inside. Replace the cover. Note: If the remote control’s LED flashes during use, the batteries are low and should be replaced.
- Page 11 Ready to Fly Flashing = Searching ON/OFF On = Paired Forward/ Left/Right Reverse Slide Trim Movement Trim Throttle Steering Ascend Forward Turn Push Turn Slide Push Slide left (Stunt mode) right left (High/low speed) right Descend Backward ON/OFF...
- Page 12 Pairing Turn on the drone. The LEDs flash. Place the drone on level ground. Turn on the remote control. The remote control’s LED flashes. Move the throttle all the way up and then down to pair the remote control with the drone. The drone’s blades remain still during pairing.
- Page 13 Land Slowly move the throttle backward to descend. Avoid moving the throttle too quickly, as it can stop the blades instantly and cause the drone to crash. After playing, turn off the remote control and drone. Stunts IMPORTANT: Make sure there is enough space for the drone to perform stunts without crashing into objects or people.
- Page 14 Troubleshooting Drone does not respond • Make sure the drone and remote control are switched on and paired. • Drone battery maybe low. Fully charge the battery. See “Charge the Drone Battery.“ • Make sure the drone is within the control range (65 ft./20 m) and in line of sight.
- Page 15 Hazardous Substances Directive,” which protects the environment by restricting specific hazardous materials and products. © 2016 General Wireless Operations Inc. All rights reserved. 08A16 RadioShack is a registered trademark used by General Wireless 2770422 Operations Inc. dba RadioShack. Printed in China radioshack.com...