Page 1
OPERATING MANUAL GAS HEAT GENERATOR WORK ON NATURAL AND LICT Industrial heating equipment READ MORE: In advance of work - suffer this file. And a few others who have been in a position to set back the tone of the lead to a job.
- When you install and work, you comply with current SECURITY INFORMATION requirements and rules regarding gas usage equipment. - Connecting the device to power should be done in strict accordance with the Operating Manual . WARNING For your own safety, make sure the ground floor is correct - When managing a device indoors provide ventilation...
Unscrew the screw at the end of the lock rod, and the air pipe in the inlet or - Do not use elements of then remove the rod and locked plate. socket of the device that the manufacturer does not recommend.
DESIGN AND PRINCIPLE DO certification DEVICE sensor Gas supply system : For the safe operation of the device, the pressure on the gas on the grid must be at least 30 mbar, but not over 60 mbar. After connecting the gas connection kit to the grid and device, open the gas tap, after which the gas will begin to be supplied through the gas filter, solenoid valve, noodles in the combustion chamber.
1,207 86 without kink! /m³K T – temperature difference in Kelvin Pakole recommends using the gas connection kits they 110/ – value returns a 10% premium for rapid have delivered, which includes a flexible hose, filter, ball warming valve.
Page 7
80 Kw 1950 Rice. 6 Total Device Dimensions DEVICE PENDANT Total Dimensions For Warning Deformation as a consequence of Heat Power Extensions Length Suspension (e.g. chain) must be at [kW] least 400 mm. Fasten it suspension under Roof Or 30 kW 1130 Ceiling On Reference beams or supports, between pillars or Against the wall.
it will continue until the air temperature in the room drops below the temperature set on the thermostat and the thermostat triggers the heating mode, in which the white INSTRUMENT CONTROL button's light signal should light up. After reaching the set temperature in the room, the thermostat turns off the The type of heat generator LH is equipped with an heating mode, stops the fan and the white light signal...
Page 9
The process of the device and, having detected any malfunction, signal the electronics - which immediately Disable device stops the device from working. Disconnect the device in the following sequence: Make sure all the buttons in Control Panel are depressed state and the lights aren't on. - Close the gas tap in front of the machine.
Page 10
SERVICE AND - Check the gas supply and the pressure of the socket on the solenoid valve that measures the noodles PREVENTIVE The device is not working after repeatedly attempting to MAINTENANCE start the ignition cycle Possible causes: Preventive maintenance - Solenoid valve damaged READ MORE:...
Page 11
Service After Sale NOTIFICATION: Never perform maintenance on an energetic or operational apparatus. This can lead to Always fuel burns or electrocution. LH-30 LH-40 LH-50 LH-60 LH-70 don' Preventive Do Perform Specialized Service Service...
If you need to change the throttle type, contact the authorized service department. APPLICATION Heat consumption for incoming air "H" is Appendix No. 1 calculated as follows: H = A.V.C . T x 10-3 Heated room: Where is A - number of air exchanges per (a) 15 m x 30 m x 4 m = 1800 m3 hour V - room volume...
Page 13
Motorcycle fan Heat Regulator Minimum gas controller 4 Ghani thermostat 5 Air flow sensor 6 Squash sensor 7 Ionitaization of flame 8 Candles Solenoid valve Capacitor...
Guarantees LH gas heat generators are guaranteed for 24 months from the date of sale, provided that the consumer is in compliance with the transport, storage and operation rules set in passport and operational manual. During the warranty period, if the consumer detects deficiencies, the manufacturer replaces the failed components and parts of the heater for free: for this purpose, the defective unit must be sent to the manufacturer by an act drafted by the gas management representative together with the owner of the heater.