Advertisement
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
11640 Harrel St. Suite B
Mira Loma, CA 91752
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7
WARNING:
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the
address above. Include the product model number, color, and a brief description of the part. Call 1-800-762-1751.
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully
NOTE: When inserting bolts, turn clockwise until tight. Then loosen
completely assembled, return to each bolt and tighten. Use wax or soap on all bolts to facilitate assembly
Read all
CUSTOMER SERVICE
CARE AND CLEANING
package all original hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
Page 1 of 7
Model No. 104858
"ROSELLE CONVERSION TODDLER
BED KIT"
1
3
-
of a turn. After crib is
2
4
Advertisement
Table of Contents
Related Manuals for baby&child 104858
Summary of Contents for baby&child 104858
- Page 1 U.S. and Canadian cribs and cradles regulations. Made in Vietnam Distributed in the U.S.A. by: Restoration Hardware Baby & Child Model No. 104858 11640 Harrel St. Suite B "ROSELLE CONVERSION TODDLER Mira Loma, CA 91752 BED KIT"...
- Page 2 IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS WARNING: ENTRAPMENT / STRANGULATION HAZARD Infants have died in toddler beds from entrapment and strangulation. Failure to follow these warnings and the assembly instructions could result in serious injury or death. NEVER use bed with children under 15 months. NEVER place bed near windows where cords from blinds or drapes may strangle a child.
- Page 3 ROSELLE CONVERSION TODDLER BED KIT WARNING: ADULT ASSEMBLY ONLY OWING TO THE PRESENCE OF SMALL PARTS, SHARP POINTS AND EDGES. CAUTION TODDLER BED: THE MINIMUM AGE SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM WEIGHT SHALL NOT BE GREATER THAN 50LBS. (22.7 KG). THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING MINIMUM DIMENSIONS OF 51-5/8 IN.
- Page 4 ASSEMBLY INSTRUCTIONS STEP #1. STATIONARY FRONT RAIL DISASSEMBLY. DETAIL A STEP #1.1: Remove the Stationary Front Rail of the crib by loosening all the bolts installed. as in DETAIL A STEP #1.2: Gently tilt the crib and release the bolts underneath the metal brackets holding the Stabilizer Rails as in DETAIL B.
- Page 5 STEP #5 TODDLER RAIL ASSEMBLY STEP #5.1: On inside face of both End Rail Panels are holes with insert nut pre-installed and holes for the wooden dowels to pass through which corresponds to the holes DETAIL C on both ends of the Toddler Rail and pre-installed wooden dowel.
- Page 6 STEP #3 MATTRESS SUPPORT HEIGHT ADJUSTMENT DETAIL D NOTE: If Mattress Supports is not in the lowest position. STEP #3.1 loosen and remove all hardware (BB) on both sides of the frame of Mattress Support. STEP #3.2 Re-install the bolt on the third hole of the frame through the hole on the arm support.
- Page 7 STEP #4 INSTALLATION OF STABILIZER RAILS INTO THE SIDE PANEL. DETAIL D STEP #4.1 On inside face of both side rail panels are pre-installed metal brackets, designed to hold the Stabilizer Rails. Set both ends of the Stabilizer Rails into brackets as illustrated in DETAIL D.
Need help?
Do you have a question about the 104858 and is the answer not in the manual?
Questions and answers