1. Manuals
  2. Brands
  3. Eastey Manuals
  4. Industrial Equipment
  5. Combination EC Series
  6. User manual

Eastey Combination EC Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
EC
Combination Series
Semi-Automatic L-Sealer & Tunnel
User Guide
EC2016T, EC2016TK,
EC2028T & EC2028TK

Advertisement

Table of Contents
loading

Related Manuals for Eastey Combination EC Series

Summary of Contents for Eastey Combination EC Series

  • Page 1 EC2016T, EC2016TK, EC2028T & EC2028TK Combination Series Semi-Automatic L-Sealer & Tunnel User Guide...
  • Page 3 Semi-Automatic L-Sealer & Tunnel User Guide Revised 01/03/2018 P/N EC001000 Rev A Copyright and Trademarks Copyright ©2017 Eastey Enterprises, Inc. All rights reserved. All trademarks and brand names are the property of their respective owners. Eastey Enterprises 7041 Boone Ave. N.

  • Page 5: Table Of Contents

    Contents Safety ..........................6 General Safety Precautions ..................6 Explanation of Symbols ....................8 Introduction ........................9 General System Description ..................9 Specifications ......................10 Dimensions and Weights..................... 12 Unpacking ........................14 Installation ........................15 Location Requirements ....................15 Operation ........................17 Main Power Disconnect ....................

  • Page 6: Safety

    Read this manual carefully and make it available to everyone connected with the supervision, maintenance, or operation of this machine. Additional copies are available on request (Eastey.com/contact-us). The development of a good safety program that is rigidly enforced is absolutely imperative when involved in the operation of industrial equipment.
  • Page 7  Do not make any modifications to either the electrical circuitry or the mechanical assemblies of this machinery. Such modifications may introduce hazards that would not otherwise be associated with this machinery. Eastey will not be responsible for any consequences resulting from such unauthorized modification. Do not operate a machine if any modification has been made ...

  • Page 8: Explanation Of Symbols

    8 Introduction Explanation of Symbols Caution sign or Safety Alert symbol. Indicates caution, be alert, Your safety is involved. Knowledge of safe operation is required. Ground symbol. Indicates ground. Use Class-3 (lower than 1000) cable to ground to earth. Incomplete grounding may lead to electrical shock. Electrical hazard.

  • Page 9: Introduction

    Introduction 9 Introduction General System Description Shrink Shrink Shrink Tunnel Magnetic Tunnel Tunnel Control Panel Disks Exit End Entrance Seal Head Takeaway Conveyor with Height Adjustment Height Adjust Product Film Roll Tray Perforator Film Roll Support Rollers Electro Built-In Magnets Drawer L-Sealer Hot Knife or...

  • Page 10: Specifications

    Specifications Explanation of Model Numbers  E = Manufactured by Eastey Enterprises Inc., division of Engage Technologies.  C = Combination (“Combo”) L-sealer and Shrink Tunnel. EC Combination Series L-sealer and Shrink Tunnels combine an L-Sealer and Shrink Tunnel on a single chassis.
  • Page 11 Introduction 11  Dual locking magnet clamps apply even pressure across the seal-bar  Adjustable dwell time for better seal control  Solid state temperature control adjustable for a variety of films  Adjustable product tray accommodates wide variety of product sizes ...

  • Page 12: Dimensions And Weights

    12 Introduction Dimensions and Weights Machine Dimensions Seal Dimensions Chamber Dimensions Shipping Model Width Height Length Front Side Width Height Length Number Weight Weight 40.5 in. 65 in. 111 in. 16 in. 20 in. 16 in. 10 in. 36 in. 1450 lbs.
  • Page 13 Introduction 13 EC2028T with PFU and Inverter See Machine Dimensions in the table at the top of the previous page for overall machine width (A), height (B), and length (C). Length Width 30 40 60 70 AIRFLOW ADJUSTMEN Height Conveyor Height (2”...

  • Page 14: Unpacking

    We are willing to assist you in every reasonable manner to help you collect claims for loss or damage. However, this willingness on Eastey’s part does not make Eastey or its parent or related companies responsible for collections or claims or replacement of equipment damaged or lost in transit.

  • Page 15: Installation

    Installation 15 Installation Lift the machine up and off of the shipping pallet. CAUTION! The EC series Combo L-sealer and Shrink Tunnel is heavy and will require a forklift, floor crane, or several people to move safely off the shipping pallet. Use proper equipment when lifting the Combo unit and ensure it is secure and will not shift while being moved off the shipping pallet.
  • Page 16 16 Installation If the combo unit is part of a longer packaging line, take into consideration the table and conveyor height in relation to adjacent machinery. The machine should be placed on a flat, level floor so that it does not rock or move. We recommend that the machine be securely locked in place when used.

  • Page 17: Operation

    Operation 17 Operation Controls for machine are grouped into two control panel areas based on the function of the machine with which they are associated.  Controls for L-sealer operation are located along the front side of the L-sealer section of the frame, just below the product tray. ...

  • Page 18: L-Sealer Control Panel

    18 Operation L-Sealer Control Panel Controls for L-sealer operation are located along the front side of the L-sealer section of the frame, just below the product tray. Controls for the L-sealer, from left to right, are as follows. 1. Power — Toggle switch to toggle L-Sealer power on or off. 2.

  • Page 19: Shrink Tunnel Control Panel

    Operation 19 Shrink Tunnel Control Panel Controls for shrink tunnel operation are located on the upper enclosure above the entrance to the shrink tunnel POWER ON ENCHUFE EN APARADO HEATER BANK BANCO de CALENTADORA CONVEYOR SPEED VELOCIDAD de TRANSPORTADOR TURN OFF FOR COOLDOWN AIRFLOW CONTRO L APAGUE PARA...

  • Page 20: Film Handling Components

    20 Operation Film Handling Components Product Tray The product tray is the adjustable metal platform used to separate the film and to facilitate insertion of the product between the bottom and top layers of film. The product tray is adjustable to achieve proper depth equal to the total width of the package, thereby allowing the product to be placed precisely at the center-fold of the film each time.
  • Page 21 Operation 21 back of the machine. Position the film roll on the rollers and tighten the bolts on the film rack collars to hold the film roll in position. Decide whether the film is an A or B wind, and then thread it through and around the idler rollers and the pin perforator.
  • Page 22 Optional PFU (Powered Film Unwinder) (With Double Film Rack for use with Film Inverting Head) Use the following steps when using the optional Eastey power film unwinder and inverting plow. These steps must be taken to ensure proper tracking of the film.
  • Page 23 Operation 23 Optional Powered Film Unwinder Sequence of Operation 1. Connect electrical power to the machine and turn on electrical power to the combo unit by lifting the main power switch lever to the On position. 2. Turn the Power toggle switch for the L-Sealer to the On position to provide power to the L-Sealer section of the combo unit.
  • Page 24 24 Operation 4. Turn the Heater Bank toggle switch at the right of the shrink tunnel Power switch to the On position to turn on the heater bank. 5. Look at the control dials to verify speeds and temperatures are set within typical levels as applicable for the type and thickness of the film you will be using.
  • Page 25 Operation 25 adjustable by turning the Conveyor timer knob, which is located to the right of the Power switch under the product tray. NOTE: If there is too much tension on the film while the bag is being sealed, the seals will be more likely to be weak or blow out in the seal area while moving through the shrink tunnel.

  • Page 26: Adjustments

    26 Adjustments Adjustments This section is presented in two parts: the first part outlines adjustments for the L-sealer; the second part outlines adjustments for the shrink tunnel section of the machine. Solid state temperature controllers for the L-sealer and shrink tunnel look similar but have slight differences in the display and number and function of programming buttons (five buttons for the L-sealer temperature controller, versus six buttons for the shrink tunnel temperature controller, for example) for making settings.
  • Page 27 Adjustments 27 1. Shut down the system and cut off electrical power by switching the Main Power Disconnect to the Off position. 2. Supporting the seal head in the up position, loosen the four set screws for the head return cylinder. Gently lower the seal head to rest on the lower seal pads. 3.
  • Page 28 28 Adjustments Turning the pot on the lower-left, you will see the numbers change inside the dial. Keep turning it until you adjust to 5 seconds. While turning this pot you will see the sec turn to min, hour, and 10hr. Factory setting is 5 seconds. Turning the selector at the lower-right, you will see the modes change.
  • Page 29 Adjustments 29 L-Sealer Temperature Controls TZ4ST TZ4ST TEMPERATURE CONT ROLLER TEMPERATURE CONT ROLLER FRONT TEMP CONTROL SIDE TEMP CONTROL Temperature controllers for the cutting rules or hot knife inserts are to the right of the speed controls in the L-sealer control panel area. The left temperature controller controls the temperature of the front seal, and the right temperature controller controls the temperature for the side seal.
  • Page 30 30 Adjustments L-Sealer Temperature Controller Adjustments SV – 2 Point Setting (°C) D Band (sec) EV – 1 Setting (°C) Control Period (sec) EV – 2 Setting (°C) Input Offset Setting (°C) Loop Break Alarm (sec) Manual Resetting (%) P Band (%) Set Key Lock I Band (sec) 1.
  • Page 31 Adjustments 31 To Change the Set Value (L-Sealer) 1. Press the left-arrow ( ) button and a digit will begin to flash. The flashing digit indicates the digit whose value can be changed by pressing the down- ( ) or up- arrow ( ) buttons.
  • Page 32 32 Adjustments Over Temperature Alarm Setting (L-Sealer) 1. Press and hold the MD button for approximately three (3) seconds.  IN-T is displayed. 2. Press and hold the MD button and up-arrow ( ) buttons at the same time for three (3) seconds to activate the menu.

  • Page 33: Shrink Tunnel Adjustments

    Adjustments 33 Shrink Tunnel Adjustments All controls specific to shrink tunnel operation of the combo unit are located above the entrance to the shrink tunnel. Shrink Tunnel Speed Controls CONVEYOR SPEED VELOCIDAD de TRANSPORTADOR AIRFLOW CONTROL Conveyor Speed Control Airflow Speed Control The shrink tunnel has two speed adjustment control dials.
  • Page 34 34 Adjustments Shrink Tunnel Temperature Controller Settings (ETC00011) The shrink tunnel temperature controller is the programmable controller located on the shrink tunnel control panel below the toggle switches for shrink tunnel power and for heater bank on / off/cooldown, and below the conveyor speed control dial. 1.
  • Page 35 Adjustments 35 To Change the Set Value 1. Press the left-arrow ( ) button and a digit will begin to flash. The flashing digit indicates the digit whose value can be changed by pressing the down- ( ) or up- arrow ( ) buttons.

  • Page 36: Conveyor Belt Tension Adjustment

    36 Adjustments To set AL-1 so the machine will shut down at 150°, press the left-arrow key and the right-most digit will flash. Use the up- or down-arrow key to select the digit, and then press the left-arrow key again. Use the up- or down-arrow key to set the digit and repeat until the correct value is displayed.

  • Page 37: Maintenance

    Maintenance 37 Maintenance The Eastey EC Combination Series Semi-Automatic L-Sealer and Shrink Tunnel will provide many hours of maintenance-free operation. To aid in the high reliability of the L- sealer and shrink tunnel, inspect the machine regularly and perform maintenance as required.

  • Page 38: L-Sealer Maintenance And Replacement

    38 Maintenance  On dead roller tunnels, clean and lubricate the conveyor chains. Check the chains and adjust as needed. Check for overall wear on dead roller guide rails and starter rails. Repair as needed.  Check the condition of the silicone covering on the rollers. Repair or replace as necessary.
  • Page 39 Maintenance 39 Changing Hot Knife Inserts and Cutting Rules 1. Disconnect the L-sealer power plug from the electrical power source. CAUTION! Always be aware of the cutting edges while replacing the knife edges. Handle the knife blades carefully. 2. Remove the #10-32 screws holding the inner side film clamp and remove the #10-32 screws holding the outer front film clamp.
  • Page 40 Instructions provided in this user guide are very general. If these generalized instructions do not address your specific conveyor issue, contact a certified representative of Eastey or contact Eastey Enterprises directly (Eastey.com/contact-us). Replacing the Takeaway Conveyor Motor NOTE: This procedure requires an Allen or hex wrench, and a 7/16-inch box-end wrench.
  • Page 41 Maintenance 41 Caution! Disconnect main power to the conveyor before attempting to repair or adjust belt. Replacing the Takeaway Conveyor Belt 1. Disconnect the L-sealer power plug from the electrical power source. 2. Loosen the idler roller to release tension until the belt is loose. 3.
  • Page 42 42 Maintenance 5. Take the belt off the conveyor rollers. NOTE: At this point, you have completed the procedure for removing the belt. Instructions from here on explain how to install the new belt or reinstall the belt if still usable. If the conveyor support plate requires replacement, replace it before installing or reinstalling the belt.
  • Page 43 Maintenance 43 Connecting Pin Drive Belt 8. Re-tension the conveyor belt as required. Refer to the instructions for Tracking the L-Sealer Conveyor Belt in the Adjustments section. Temperature Controller Replacement NOTE: Because of similar physical design this procedure is applicable for temperature controllers for the L-sealer or the temperature controller for the shrink tunnel.

  • Page 44: Shrink Tunnel Maintenance And Replacement

    44 Maintenance For the second option (to replace entire controller and receptacle), first take note of wire locations (make a sketch and label the wires with tape, if necessary), and then disconnect wires from the temperature controller and thermocouple. Slide the controller and receptacle out of the front of the panel.
  • Page 45 Maintenance 45 Caution! Make sure the conveyor is stopped before putting your fingers or anything else in the conveyor area. 3. Remove film residue. If necessary, use a dull blunt-edged tool. Do not use any sharp instruments, as nicking silicone may result in damage that requires replacing the roller covering.
  • Page 46 46 Maintenance 7. Check conveyor chain tension by following the procedure outlined in the Adjustments section. Idler, Roller Shaft, Bearings, or Sprockets Replacement Refer to the preceding Roller Silicone Covering Replacement section to access and remove rollers as required. Note the location and orientation of sprockets (make a sketch and note measurements if necessary).
  • Page 47 Maintenance 47  If repairing a belt - Tie two undamaged strands at the end to be spliced together with cord, twine, or wire ties. - Cut out the damaged wire(s) with a wire cutters — pick out and dispose of wire pieces immediately.
  • Page 48 48 Maintenance 6. Pull the ends of the strand through until the center section “pops” or “locks” into place. (You should be pulling the strands toward you.) 7. Use pliers or the wire belt straightening tool to straighten the wire in the center space.
  • Page 49 Maintenance 49 2. Bend the wire toward the center and insert it around the z-bend next to the center space. (Space D in the following illustration.) 3. Pull the strand wire through the mesh and straighten it with pliers. 4. Repeat the above three moves until you reach the side edge of the belt. 5.
  • Page 50 50 Maintenance 2. If you are installing a new belt, you are finished splicing. Step 4 – Check Drive Shaft Sprocket Alignment  Check to ensure 3/16-inch clearance between all sprockets (and/or blanks) and the Z-bends next to them.  Check alignment of sprocket teeth with a straight-edge. (Only necessary if the sprockets are not keyed to the drive shaft.) Step 5 –...
  • Page 51 Maintenance 51 Replacing Shrink Tunnel Chamber Components Caution! Disconnect main power source before performing any procedure to replace any tunnel component(s). NOTE: Because of similar physical design, the procedure for removing or replacing the temperature controller for the shrink tunnel is very similar to the procedure for the L-sealer temperature controllers.
  • Page 52 52 Maintenance Replacement of Upper Wear Rails Shut off power to the machine, move the conveyor by hand if necessary to gain access. Remove the #10-32 screw on the idler end. Replace parts in the same manner in which they were disassembled. Chamber Cooling Fan Motor Replacement Shut off power to the machine.

  • Page 53: Troubleshooting

    Troubleshooting 53 Troubleshooting Troubleshooting L-Sealer Issues Problem Solution  Check to be sure sealer is plugged in No Element Heat and electrical power is present at the outlet.  Is the display for temperature on? If not, check main fuses. ...
  • Page 54 54 Troubleshooting Problem Solution  Is timer working properly? Magnet Hold Down Magnets Not Operating Magnet Sealers - The timer is identical to the timer used for (Sealing head will not stay down, the Conveyor. See items to check on the sealer operates normally...
  • Page 55 Troubleshooting 55 Problem Magnet Hold-Downs Stay Engaged When They Should Release Solution  When you turn the power off, do the magnets release? - If they do not, replace the magnets. POWER POWER sec. sec. MODE MODE AT11DN AT11DN Speed Pot Mode Selector Mode Selector Speed Pot...
  • Page 56 56 Troubleshooting Problem Solution  Improper setting of temperature film cutoff Charring of Film controller. (Too much heat.) Adjust temperature down. Troubleshooting Shrink Tunnel Issues The following illustration shows the D.C. board used in the shrink tunnel. Some of the solutions to problems identified in the troubleshooting table that follows refer to adjustments made by tuning potentiometers on this board.
  • Page 57 Troubleshooting 57 Problem Solution  The conveyor motor is controlled by a D.C. Conveyor not moving control board. Input is 220 VAC in and variable 0 to 90 VDC out.  Is a green light on? If not, check the input fuse. ...
  • Page 58 58 Troubleshooting Problem Solution No air flow 1. Check AC Inverter adjustable speed pot settings below.  C.L.: Set at approximately 12 o’clock.  Max.: All the way counter-clockwise.  Min.: All the way clockwise.  ACC.: All the way clockwise. ...
  • Page 59 Troubleshooting 59 Color and Color and Flash Sequence After Drive Status Sequence Flash Rate Recovered Fault — Normal Operation (Run) Green 1 sec. On / Off Overload (120% – 160% Full On continuously Green Load — t (Drive Timed Out) 0.25 sec.
  • Page 60 60 Troubleshooting Problem Solution No heat 1. Is the display on the temperature controller on? If not, check for 220 Volts on terminals 9 and 10. If there voltage, replace temperature controller. 2. If the display is on and SV is set higher than PV, is there a red light on? If not, replace the thermocouple.
  • Page 61 Troubleshooting 61 Menu 2 Temperature Controller 1 Temperature Controller 2 Su-2 Su-2 (same as 1) AL-2 (same as 1) AHYS - AHYS - (same as 1) (same as 1) (same as 1) (same as 1) IN-B IN-B (same as 1) REST - REST - (same as 1)

  • Page 62: Parts List

    62 Parts List Parts List Electrical — L-Sealer Q’TY. DESIGNATOR PART NO. DESCRIPTION EAST0421-1 25 Amp, 220 V, 2 pole contactor, GE EAST0421 25 Amp, 220 V, 2 pole contactor, S&S F1 & F2 ET000301 10 Amp Fuse (16T) ETL00240 15 Amp Fuse (28T) ETC00309 Power On/Off...
  • Page 63 Parts List 63 Q’TY. DESIGNATOR PART NO. DESCRIPTION EAST0494 Temperature Controller (Watlow) Heater, Side, 20” Cartridge, Heater 20”, 220 V EAST0496 Heater, Front, 16” Cartridge, Heater, 16” EAST0497 Heater, Front, 28” Cartridge, Heater, 28” EAST0555 SSR-1 Front EAST0495 Solid State Relay SSR-2 Side EAST0495 Solid State Relay...
  • Page 64 64 Parts List Mechanical — L-Sealer PART NO. DESCRIPTION I0000007 Actuator, Inverted EAST0512 Actuator, Non-Inverted Arm Casting, Infeed – 20” EAST0508 Arm Casting, Outfeed – 20” EAST0507 EAST0061 Barrel Nut, Conveyor EAST0052 Bearing, Conveyor Guide / Idler Roller EAST0378 Bearing, Film Rack Roller - Large EAST0380 Bearing, Film Rack Roller - Small EAST0254...
  • Page 65 Parts List 65 PART NO. DESCRIPTION Caster, 3” × 1-¾” EAST0044 Collar, 1” Rear Shaft EAST1018 Collar, ¼” Power Film Unwind EAST1020 EAST0043 Conduit EAST0597 Conduit - Bracket Conduit Connector, ½”, 90-degree EAST0101 Conduit Connector, ½” straight with nut EAST0102 EAST0214 Conveyor Adjusting Bracket EAST0057B...
  • Page 66 66 Parts List PART NO. DESCRIPTION Duo Seal Arrow Insert, 28-inch Front Bar – Supra Silverstone EAST0926 Duo Seal Arrow Insert, 20-inch Side Bar – Supra Silverstone EAST0918 Duo Seal Arrow Insert, 30-inch Side Bar – Supra Silverstone EAST0925 Duo Seal Mushroom Insert, 16-inch Front Bar – Supra Silverstone EAST0919 Duo Seal Mushroom Insert, 28-inch Front Bar –...
  • Page 67 Parts List 67 PART NO. DESCRIPTION Head Return Cylinder – Retro Fit Kit (EM2016, EC2016, EM2028 & EC2028) SUB00047 EAST0084 Hole Punch Ball EAST0085 Hole Punch Casting EAST0083 Hole Punch Die EAST0268 Hole Punch Knob EAST0086 Hole Punch Solenoid, Electric EAST0087 Hole Punch Strain Relief Connector EAST0511...
  • Page 68 68 Parts List PART NO. DESCRIPTION EAST0022 Pillow Block, 1-inch EAST0367 Pin Perforator Guard EAST0368 Pin Perforator Lower Pad Pin Perforator Wheels – For 5/8” Shaft EAST0366 EAST0156 Product Separator Tray and Tubes on Frame - ¾ Snap ring, Heavy Duty Product Separator Tray, 20”...
  • Page 69 Parts List 69 PART NO. DESCRIPTION Safety Shield, Front – Outer EM2016 & EC2016, 17” EAST0521 Safety Shield, Front – Outer EM2028 & EC2028, 28” EAST0553 Safety Shield, Side – Inner EM2016, EC2016, EM2028 & EC2028 EAST0522 Safety Shield, Side – Outer EMC2016, EC2016, EM2028 & EC2028 EAST0523 EAST0008 Seal Bar, 16-inch Front-Lower...
  • Page 70 70 Parts List PART NO. DESCRIPTION PTFE Tape, ½-inch – 10 Mil × 36 yards EAST1006 PTFE Tape, ¾-inch – 10 Mil × 10 yards EAST0201 PTFE Tape, ¾-inch – 10 Mil × 36 yards EAST1005 EAST0494 Temperature Controller EP000535 Thermocouple Timer, SignaLine –...

  • Page 71: Appendix A: Electrical Schematics

    Appendix A: Electrical Schematic 71 Appendix A: Electrical Schematics Panel Layout — L-Sealer Pulse Conv. L.S. L.S. Magnet Transformer Main Main Fuse Fuse Block Block wire way Bridge Solid State Rectifier Relays SSR1 SSR2 Relay wire way Temperature Temperature Control Control Dwell Timer...
  • Page 72 72 Appendix A: Electrical Schematic Panel Layout — Shrink Tunnel POWER HEATER BANK DC CONTROL CONVEYOR BLOWER SPEED SPEED CONTROL CONTROL...

  • Page 73: Electrical Schematic

    Appendix A: Electrical Schematic 73 Electrical Schematic — L-Sealer...
  • Page 74 74 Appendix A: Electrical Schematic Electrical Schematic — Shrink Tunnel Variable Speed, 220V 40/50A / 480V 20/25A Single-Phase...

  • Page 75: Appendix B: Temperature Setting Specifications For Shrink-Wrap Plastics

    Appendix B: Temperature Setting Specifications for Shrink Wrap Plastics 75 Appendix B: Temperature Setting Specifications for Shrink-Wrap Plastics Mushroom Insert PVC (Poly-Vinyl Chloride) Temperature settings: 325° F front bar; 325° F side bar Pad type: Felt Dwell Time: Approximately 1 second Polyolefin Temperature settings: 335°...

  • Page 76: Appendix C: L-Sealer Size Estimating

    76 L-Sealer Size Estimating Appendix C: L-Sealer Size Estimating L-Sealer Center-Folded Film Size Estimating Table To calculate estimated per-package cost for manual and semi-automatic L-sealers, use the following formulas. 1) Center-Folded film – width of roll of film = 2) Cutoff Film length – film going across front seal bar = 3) Film usage –...

  • Page 77: 16-Inch Side Seal Package Size Estimation

    L-Sealer Size Estimating 77 16-inch Side Seal Package Size Estimation The following Eastey Enterprises side seal bar size dimensions are provided to make sure your product will fit under the side seal bar. You will need to know your product height and width to use these figures effectively.

  • Page 78: Warranty Statement

    EM Performance Series Semi-Automatic L-Sealers Warranty Statement Eastey Enterprises warrants that all of the products it ships will be in good working order and free from defects in material and workmanship for a period of two (2) years from the date of shipment by Eastey and will conform to the published specifications for that product.
  • Page 79 Warranty Statement 79 defective component to Eastey. If, after 30 days, Eastey hasn’t received the defective component, the customer will be invoiced for the replacement component. If the returned component is found to not be elegible for warranty, Easty will contact the customer and the customer will be invoiced for the replacement component.

  • Page 80: Customer Support

    For help setting up or operating the EM Performance Series L-Sealer, please contact Eastey Technical Service at one of the numbers listed below. Toll-Free Phone 800-835-9344 Phone 763-428-4846 763-795-8867 E-mail info@eastey.com www.eastey.com Thank you again for your purchase of Eastey products. We are pleased to be a part of your packaging needs.

This manual is also suitable for:

Combination ec2016tCombination ec2016tkCombination ec2028tCombination ec2028tk

Table of Contents