Advertisement
Quick Links
Limpido Z2
Salt electrolysis
pH regulator
NB:
Read these instructions
carefully before installing,
starting up or using this
appliance.
Reference
Version
MPNT0301
V1.0 (EN)
Technical Instructions v1.0
Date
04/05/2017
Table of contents
features................................................................................................. 2
Presentation .......................................................................................... 2
Installation ............................................................................................ 3
START-UP ............................................................................................. 6
Maintenance ....................................................................... 12
Advertisement
Related Manuals for ccei Limpido Z2 25
Summary of Contents for ccei Limpido Z2 25
-
Page 1: Table Of Contents
Technical Instructions v1.0 Limpido Z2 Salt electrolysis pH regulator Read these instructions carefully before installing, starting up or using this appliance. Table of contents features....................2 Presentation ..................2 Installation .................... 3 START-UP ..................... 6 Maintenance ............... 12 Reference Version Date MPNT0301 V1.0 (EN) -
Page 2: Features
CCEI Limpido Z2 v1.0 FEATURES Limpido Z2 Limpido Z2 Limpido Z2 General Model Sizes Max production 4g/h 8g/h 12g/h (lxhxp) 300x150x90 Weight Tank volume 10 à 25m 20 à 50m 30 à 75m Supply 230V/50Hz Cleaning of cell Polarity inversion... -
Page 3: Installation
CCEI Limpido Z2 v1.0 The electrolysis cell As an essential component of your system, the cell is equipped with electrodes consisting of titanium with ruthenium treated plates. It is specially designed to guarantee a large lifespan and limit maintenance operations. - Page 4 CCEI Limpido Z2 v1.0 Suction strainer immerse on the tank of correction fluid (PH- or PH+) Use the clamp saddles. Screw injector on the TEFLON clamp. Connect the probe. To connect to the pool, use clamp saddles, probe support and probe. All screwings must be done with TEFLON.
- Page 5 CCEI Limpido Z2 v1.0 NJECTOR INSTALLATION The injector permits to inject PH- and PH+ product necessary quantity to correct the pH of water. The injector has absolutely to be placed after PH probe and as close as possible to the pool outlet.
-
Page 6: Start-Up
CCEI Limpido Z2 v1.0 START-UP NB: ONLY REGULAR ANALYSIS ENABLES THE RIGHT CONFIGURATION OF THE APPLIANCE Carefully following the stages below will guarantee a problem-free start-up. SALT LEVEL CONTROL Limpido Z2® is designed to operate with a water conductivity corresponding to a salinity rate between 1.5g/l and 3,5g/l at 25°C. - Page 7 CCEI Limpido Z2 v1.0 ONTROLLING THE AND THE At the time of installation, you are advised to test or commission a specialist to test the TAS (Total Alkali Strength) and/or the TH (Total Hardness) of the pool water. The two measurements are generally close to each other and are more often than not expressed in French degrees (°F).
- Page 8 CCEI Limpido Z2 v1.0 Alternately indications of the system status are possibly displayed: Status Description Filt. Stop Filtration pump is stopped. No regulation. Temp. ↓ The current temperature is lower than the minimal set temperature in the electrolysis menu. No treatment below this temperature.
- Page 9 CCEI Limpido Z2 v1.0 pH : 00.00L This display shows the total volume of injected pH liquid since the first operation; Prod Cl : 31h23m Cell ZLA 60 It shows the total duration of chlorine production since the first operation alternatively with cell model (60m3 in the above example) ZLA 25 = 25 m3 cell («...
- Page 10 CCEI Limpido Z2 v1.0 This display allows to set the volume of the pH liquid tank. The volume of the tank is adjustable from 0 to 25L. To enter it, press the button and select the value using the buttons and .
- Page 11 CCEI Limpido Z2 v1.0 With this menu you can set the current production level. It is set default at 80% and it is possible to set this value between 20 and 100%. ATTENTION The nominal value is 80%. To set it at a greater value will enable to produce more chlorine but will at the same time reduce the lifetime of the cell (increase of the areal current density).
-
Page 12: Maintenance
CCEI Limpido Z2 v1.0 AINTENANCE OVER WINTER In winter, weather permitting, the treatment can be maintained by considerably reducing frequency. An 8-hour filtration cycle every fortnight is sufficient in most cases. However, it is vital to continue to monitor the salt rate to preserve the cell operating in water which is under- salted to an excessive degree (<2g/l). - Page 13 CCEI Limpido Z2 v1.0 There can be several reasons of a point of 0 shift: - The electrolyte may have been polluted by liquid entering the sensor - Polluted junction - Probe used in an installation with leakage currents caused by a bad earth electrode (In this case, regeneration is pointless).
- Page 14 CCEI Limpido Z2 v1.0 ® IMPIDO Date of purchase: Serial N°: Declaration Bleu Electrique SAS (FR 47 403 521 693) declares that the Limpido Z2® product fulfils the safety and electromagnetic compatibility requirements of European Directives 2006/95 / EC and 2004/108 / EEC.