Related Manuals for AquaCo SYS-925
Summary of Contents for AquaCo SYS-925
-
Page 1: Twin Undersink Water Filtration System
Twin Undersink Water Filtration System Installation Product Code: SYS-925 WARNING: For correct operation & installation, it is essential to observe these instructions TWIN UNDERSINK WATER FILTRATION SYSTEM Page 1 of 12... -
Page 2: Table Of Contents
Twin Undersink Water Filtration System Installation Product Code: SYS-925 CONTENTS Twin Undersink Water Filtration System ............................. 1 Installation and Operation Manual ..............................3 AquaCo Customer Service ................................3 Operation ...................................... 3 Installation ..................................... 4 Installation requirements ................................4 Typical Installation ..................................4 Installation Procedure ................................ -
Page 3: Installation And Operation Manual
AQUACO CUSTOMER SERVICE Thank you for purchasing an AquaCo undersink water filter system. Your system is a proven performer manufactured from only quality materials and components and will give years of ‘spring fresh’ water free of impurities if maintained properly. -
Page 4: Installation
Twin Undersink Water Filtration System Installation Product Code: SYS-925 INSTALLATION This system comes complete with an installation kit enabling it to be connected to 15mm (½”) copper pipe (cold supply only - hot water should be filtered prior to heating). Included is a control valve incorporating backflow prevention, anti hammer, flow control and pressure limiting capabilities in full compliance with the relevant laws. -
Page 5: Installation Procedure
Twin Undersink Water Filtration System Installation Product Code: SYS-925 INSTALLATION PROCEDURE 1. Select suitable location that is close to the point of filtered water delivery (eg. sink). Remember to allow access room for changing filters and a suitable place where water spillage will not cause damage. Location should not be in direct sunlight. -
Page 6: Cartridge Installation/Maintenance
Twin Undersink Water Filtration System Installation Product Code: SYS-925 CARTRIDGE INSTALLATION/MAINTENANCE To change the filter cartridges, adhere to the following procedure. Figure 4 1. Close 1/2" Tee with 1/4" Push-In Tube Connector (Mains Connector or Shut Off Valve) to prevent water flow. -
Page 7: Faucet Installation Procedure
Twin Undersink Water Filtration System Installation Product Code: SYS-925 Figure 8 – Faucet Installation Diagram Important note: Battery must be replaced when changing cartridges. FAUCET INSTALLATION PROCEDURE 1. Remove the black battery seat from the faucet lever handle (see Figure 9). -
Page 8: Guide To Use Push-In Tube Connectors
Twin Undersink Water Filtration System Installation Product Code: SYS-925 GUIDE TO USE PUSH-IN TUBE CONNECTORS Figure 12 USE GUIDELINES • Minimum operating pressure 200 kPa. • Maximum operating pressure 520 kPa. • Do not allow exposure to temperatures below 0°C. -
Page 9: Cartridge Replacement Guide
Twin Undersink Water Filtration System Installation Product Code: SYS-925 CARTRIDGE REPLACEMENT GUIDE You can obtain replacements from your local AquaCo dealer. To maintain performance, warranty and standards use genuine AquaCo replacements. Figure 10 Page 9 of 12... -
Page 10: Performance Data Sheet
TO MAINTAIN THE HIGH QUALITY OF THE PURIFIED WATER THE CARTRIDGE(S) NEED CHANGING EVERY 6-18 MONTHS (THIS IS DEPENDENT ON WATER QUALITY AND USAGE). YOU CAN OBTAIN REPLACEMENT CARTRIDGES FROM YOUR LOCAL AQUACO STOCKIST. TO MAINTAIN PERFORMANCE AND WARRANTY USE GENUINE AQUACO REPLACEMENTS. - Page 11 Twin Undersink Water Filtration System Installation Product Code: SYS-925 PRODUCT CODE: ARA-925 ARAGON FILTER Micron Rating >100% @5 μm Filter Dimensions 9” x 2.5” Suspended impurities (rust, sand, algae, other particles) over 100% 5 µm Heavy and radioactive metals (lead, cadmium, copper, >99%...
-
Page 12: Notes
Applicable to all above, is that the Warranties need to be approved by AquaCo to ensure product was not incorrectly used, installed or claimed.
Need help?
Do you have a question about the SYS-925 and is the answer not in the manual?
Questions and answers