Bush ELED24HDSDVDWB Instruction Manual page 39

Advanced features
Getting the most from your TV
• You must change your modem's SSID when there are
any other modems around with the same SSID. You can
encounter connection problems otherwise. Use a wired
connection if you experience problems with a wireless
connection.
Configuring Wireless Device Settings
Open the Network menu and select Network Type as
Wireless Device to start connection process.
Highlight Scan Wireless Networks option and press OK
to start a search for available wireless networks. All found
networks will be listed. Highlight your desired network
from the list and press OK to connect. A network with
hidden SSID can not be detected by other devices. If you
want to connect to a network with hidden SSID, scroll
down the list of detected wireless networks, highlight
the Add New Network option and press OK. Enter the
name of the network and select the security type using
the related options to connect.
Note: If the modem supports N mode, you should set
N mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use this
keyboard via the directional buttons and the OK button
on the remote control.
Wait until the IP address is shown on the screen.
This means that the connection is now established. To
disconnect from a wireless network, highlight Network
Type and press Left or Right buttons to set as Disabled.
If your router has WPS, you can directly connect to
the modem/router without entering a password or
adding the network first. Highlight Press WPS on your
wifi router option and press OK. Go to your modem/
router device and press the WPS button on it to make
the connection. You will see a connection confirmation
on your TV once the devices have paired. Select OK to
proceed. No further configuration is required.
Highlight Internet Speed Test and press the OK button
to check your internet connection speed. Highlight
Advanced Settings and press the OK button to open
the advanced setting menu. Use directional and numeric
buttons to set. Highlight Save and press the OK button
to save settings when complete.
Other Information
The status of the connection will be displayed as
Connected or Not Connected and the current IP address,
if a connection is established.
If you require any technical guidance or find that your TV is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
or online at www.bush-support.co.uk If you still require further assistance, call one of our experts on 0345 604 0105, a Bush enquiry line.
Connecting to your mobile device via WLAN
• If your mobile device has WLAN feature, you can
connect it to your TV via a router, in order to access
the content in your device. For this, your mobile device
must have an appropriate sharing software.
Connect your TV to your router following the steps
mentioned in the sections above.
Afterwards, connect your mobile device to the router and
then activate the sharing software on your mobile device.
Then, select files that you want to share with your TV.
If the connection is established correctly, you will be able to
access the shared files installed on your mobile device via the
Audio Video Sharing feature of your TV.
Highlight the Audio Video Sharing option in the Sources
menu and press OK, available media server devices in the
network will be displayed. Select your mobile device and
press the OK button to continue.
• If available, you can download a virtual remote controller
application from the server of your mobile device
application provider.
Note: This feature may not be supported on all mobile
devices.
Networked Standby Mode
Networked Standby Mode is standard that allows a
device to be turned on or woken up by a network
message. The message is sent to the device by a program
executed on a remote device connected to the same
local area network, such as a smartphone.
Your TV is WoL and WoWLAN compatible. This feature
might be disabled during the First Time Installation
process. To enable this feature set the Networked
Standby Mode option in the Network menu as On. It is
necessary that both the device, from which the network
message will be sent to the TV, and the TV are connected
to the same network. Networked Standby Mode feature
is only supported for Android OS devices and can only
be used via YouTube and Netflix applications.
In order to use this feature the TV and the remote device
should be connected at least once while the TV is on.
If the TV is powered off, the connection should be re-
established, the next time it is switched on. Otherwise this
feature will be unavailable. This does not apply, when the
TV is switched into the standby mode.
The performance of some devices in the market,
may vary due to the software architecture. In order to
use Networked Standby Mode feature with a better
performance, please make sure that your device has latest
firmware version.
Advanced features 37