Sony CCU-550A Operation Manual page 23

4 OUTPUT connectors
Y/G, R-Y/R, B-Y/B (component video signal /RGB
output) connectors (BNC type)
Supply the component signals or the R, G, and B
signals for the chroma keyer from each connector.
Use the switch on the internal VA board to select the
signals to be output.
For details on the internal boards, refer to System Manual.
VBS1/2/3 (composite video signal 1/2/3 output)
connectors (BNC type)
Supply the signal from the video camera in composite
format.
Use the switch on the internal VA board to select the
composite video signal or sync signal.
When the sync signal (0.3 Vp-p, 75 ohms) is selected,
connect the VBS 3 connector to the sync signal input
connector on a waveform or picture monitor.
WF (waveform monitor output) connector (BNC
type)
Supplies a video signal to a waveform monitor.
The WAVEFORM MONITOR button on the optional
MSU-700/750 Master Setup Unit, MONITOR
SELECT button on the RCP-740/741 Remote Control
Panel, or MONITOR SELECT control on the BKP-
5973 CCU Control Panel selects the signal output from
the WF connector. Changing the signal output from
the WF connector on the RCP-740/741 or the BKP-
5973 simultaneously changes the picture on the picture
monitor.
WF MODE (waveform monitor mode) connector
(4-pin)
Connects to the corresponding connector on a
waveform monitor to allow the sequential monitoring
of signals.
PIX (picture monitor output) connector (BNC type)
Supplies a video signal or video and character signals
together to a picture monitor.
Use the PICTURE MONITOR button on the MSU-
700/750, MONITOR SELECT button on the RCP-740/
741, and MONITOR SELECT control on the BKP-
5973 to select the signal output from the PIX
connector. When the signal output from the PIX
connector on the RCP-740/741 or the BKP-5973
changes, the waveform output on the waveform
monitor also changes.
5 SERIAL OUTPUT (serial digital video/audio
output) connectors (BNC type)
Supply the video/microphone signals from the video
camera in serial digital format. These connectors are
active only when the optional BKP-5972 SDI Output
Board is attached to the CCU-550A/550AP. Connect
to a digital video switcher or component digital VTR.
6 MIC REMOTE (microphone remote control)
connector (D-sub, 15-pin)
Connects to an external control unit such as an audio
mixer. With the connected unit, you can set the
microphone input level of the video camera to –60,
–50, –40, –30, or –20 dB. You can also set the
microphone input level with a switch on the internal
AT board.
For details on the internal boards, refer to System Manual.
7 INTERCOM/TALLY/PGM (program audio)
connector (D-sub, 25-pin)
Inputs/outputs intercom, tally, or program audio
signals. Connects to an intercom, tally, or program
audio connector of an intercom system.
8 RCP/CNU REMOTE (remote control panel/
camera command network remote) connector (8-
pin)
Connects to the MSU-700/750 Master Setup Unit,
CNU-700/500 Camera Command Network Unit, RCP-
700 Series Remote Control Panel or RM-B150 Remote
Control Unit with an optional CCA-5 connecting cable
to transmit/receive control signals.
When the remote control panel or the remote control
unit is connected, power is supplied to the remote
control panel or the remote control unit through this
connector.
9 COAX (coaxial) connector (BNC type)
Accepts and supplies signals from/to the video camera
according to the setting of a switch on the internal DM
board. Power is not supplied to the camera through
this connector. Connect a coaxial cable to this
connector.
!º AC IN (AC power input) connector
Connects to an AC power source using the supplied
AC power cord. Secure the power cord to the CCU-
550A/550AP using the supplied plug holder.
7(E)