Makita UH200D Instruction Manual page 16

Store the tool in the place not exposed to water and rain.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
For cordless grass shear use
(Fig. 30)
Optional accessory
This tool can be used as a grass shear by using the grass
shear blade (optional accessory) and 2-way change set.
To use this tool as a grass shear, replacing the hedge
shear blades with the grass shear blades is required.
For removing the hedge trimmer blades, refer to the
aforementioned section titled "Removing the hedge shear
blades".
For installing the grass shear blade, refer to the section
below titled "Installing or removing grass shear blades".
• Grass shear blade assembly (for Grass Shear)
• 2-way change set consisting of the following three
accessories
- Grass shear blade cover (for Grass Shear)
- Storage case (for blade bottom section)
- Base frame (for Grass Shear)
• Long handle attachment (for Grass Shear)
ASSEMBLY
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out any
work on the tool.
Installing or removing blade cover
(Fig. 31 & 32)
CAUTION:
• Be careful not to contact the shear blade when
installing or removing the blade cover. Contacting the
shear blade may cause personal injuries.
Slide the blade cover from the tool's side until the shear
blade completely hides itself and then push in it lightly
towards the tool from the front.
To remove the blade cover, take the above installation
procedure in reverse.
Installing or removing grass shear blades
CAUTION:
• Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing shear blades. Failure to switch off and
remove the battery cartridge from the tool may result in
serious injury from accidental start-up.
• When replacing the shear blade, always wear gloves
without removing blade cover so that hands and face
does not directly contact the blade. Failure to do so
may cause personal injury.
NOTE:
• Do not wipe off grease from the gear and crank. Failure
to do so may cause damage to the tool.
16
• For specific way of removing and installing shear
blades refer to the reverse of a package for accessory
shear blades. (Fig. 33)
To install the grass shear blade, prepare the crank,
undercover and new grass shear blade. (Fig. 34)
Take out the blade cover from the old shear blades and fit
it onto the new ones for easy handling during the
replacement of blades. (Fig. 35)
Adjust the three detent pin position so that these pins are
lined up at right angle in relation to the basic alignment
line on the tool housing. (Fig. 36)
Fit the crank with its recessed part facing upwards onto
the detent pins. At this time, apply a small amount of
grease to the periphery of the crank using grease that the
shear blades as optional accessory are provided with or
that remains inside gear housing. (Fig. 37)
Overlap the oval hole in the upper blade with that in the
lower one. Move the shear blades so that the hole in the
base plate of shear blades are positioned in the center of
these overlapped oval holes. (Fig. 38)
Turn the shear blades upside down and install it so that
the detent pins on the tool fit in the hole in the shear
blades. Make sure that the shear blades are set in place
securely as far as they reach the base plate. (Fig. 39)
Place the undercover so that the symbol
undercover is aligned with the symbol
lever. (Fig. 40)
Press the undercover down and with the undercover
pressed down turn the undercover clockwise until the
symbol on the label is aligned with the symbol
locking lever (the undercover is completely locked).
(Fig. 41)
At this time, make sure that the locking lever fits in the
groove in the undercover.
Remove the blade cover and then turn on the tool to
check it for proper movement.
NOTE:
• When the shear blades does not operate properly,
there is a poor fit between the blades and crank. Redo
from the beginning. (Fig. 42)
Remove the base frame and place the tool upside down.
CAUTION:
• Before placing the tool upside down, be sure to remove
the base frame (only for the tool changed to the grass
shear mode). (Fig. 43)
To remove the shear blade, press the locking lever and
with the locking lever pressed turn the undercover
counterclockwise until the symbol
aligned with the symbol
Take out the undercover, shear blade and crank in order
from the tool. (Fig. 45)
NOTE:
• In the 2-way usage, the removed hedge shear blade
need to be sheared in the blade storage case and then
stored for future use.
Installing or removing base frame
CAUTION:
• Before installing or removing base frame, be sure to
install the blade cover.
on the
on the locking
on the undercover is
on the locking lever. (Fig. 44)
on the