Makita UH200D Instruction Manual
Cordless hedge trimmer
Hide thumbs
Also See for UH200D:
- Instruction manual (136 pages) ,
- Technical information (8 pages) ,
- Instruction manual (112 pages)
Related Manuals for Makita UH200D
Summary of Contents for Makita UH200D
- Page 1 INSTRUCTION MANUAL Cordless Hedge Trimmer UH200D 010965 IMPORTANT: Read Before Using.
-
Page 2: Specifications
EC Declaration of Conformity and returned to an environmentally Makita Corporation responsible compatible recycling facility. manufacturer declare that the following Makita ENE014-1 machine(s): Intended use Designation of Machine: The tool is intended for trimming hedges. Cordless Hedge Trimmer... -
Page 3: General Power Tool Safety Warnings
Europe who is: Do not expose power tools to rain or wet Makita International Europe Ltd, conditions. Water entering a power tool will Michigan, Drive, Tongwell, increase the risk of electric shock. - Page 4 hazards. cause irritation or burns. Power tool use and care Service 17. Do not force the power tool. Use the correct 28. Have your power tool serviced by a qualified power tool for your application. The correct repair person using only identical replacement parts.
-
Page 5: Personal Protective Equipment
GEB070-2 recommend the use of a residual-current-operated circuit breaker (ground-fault circuit interrupter) with CORDLESS GRASS SHEAR a tripping current of 30 mA or less, or an earth SAFETY WARNINGS leakage current protector. 10. Work gloves of stout leather are part of the basic WARNING! IMPORTANT READ CAREFULLY all equipment of the hedge trimmer and must always safety warnings and all instructions BEFORE USE . - Page 6 entangled. Wear protective hair covering to authorized service center unless indicated contain long hair. elsewhere in this manual. Wear eye protection and stout shoes at all times Switch on the motor only when the hands and feet while operating the machine. are away from the cutting tool.
-
Page 7: Functional Description
replacing cutting tools or cleaning the equipment flow, overheating, possible burns and or cutting tool. even a breakdown. Check loose fasteners and damaged parts such Do not store the tool and battery cartridge in as cracks in the cutting attachment. locations where the temperature may reach or exceed 50 ﾟ... -
Page 8: Operation
Do not use force when inserting the battery • cartridge. If the cartridge does not slide in easily, it To start the tool, depress the lock-off button and pull the is not being inserted correctly. switch trigger. Release the switch trigger to stop. The lock-off button can be pressed from either right or left Switch action side. - Page 9 Do not attempt to cut branches thicker than 10 mm diameter with this trimmer. These should first be cut with shears down to the hedge trimming level. CAUTION: Do not cut off dead trees or similar hard objects. • Failure to do so may damage the tool. Do not trim the grass or weeds while using hedge •...
-
Page 10: Maintenance
After operation, remove dust from both sides of the blade 1. Clamping nuts with wired brush, wipe off it with a rag and then apply 2. Chip receiver enough low-viscosity oil, such as machine oil etc. and 3. Screws on the spray-type lubricating oil. - Page 11 Installing the hedge shear blades 1. Undercover 010892 Take out the undercover from the tool. 1. Screws 1. Crank 2. Undercover 3. Shear blades 010904 Prepare the crank, the undercover and new shear blades. 010893 Loosen two screws with a coin and similars and remove the shear blades.
- Page 12 shear blades as optional accessory are provided with or 1. Screws that remains inside gear housing. 010910 Tighten two screws with a coin or similars firmly. 1. Oval holes that are overlapped 1. Locking lever 2. Hole in the base plate of shear blades 2.
- Page 13 Only use accessory or attachment for its stated purpose. Storage If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. 1. Hook hole Hedge shear blade cover • Hedge shear blade assembly •...
- Page 14 accessory shear blades. ASSEMBLY CAUTION: Always be sure that the tool is switched off and the • battery cartridge is removed before carrying out any work on the tool. Installing or removing blade cover CAUTION: Be careful not to contact the shear blade when •...
- Page 15 lever. 1. Recessed part of crank 2. Pins 3. Crank 4. Apply grease 010898 Fit the crank with its recessed part facing upwards onto 010902 the detent pins. At this time, apply a small amount of Press the undercover down and with the undercover grease to the periphery of the crank using grease that the pressed down turn the undercover clockwise until the shear blades as optional accessory are provided with or...
- Page 16 When installing or removing base frame, take care • 1. Undercover that your fingers are not be pinched between the 2. Locking lever tool and base frame. 3. Press 4. Turn 1. Groove 2. Base frame 010888 To remove the shear blade, press the locking lever and with the locking lever pressed turn the undercover counterclockwise until the symbol on the undercover...
- Page 17 Do not let the shear blades contact the grounds • OPERATION during operation. The blades will be dulled, causing poor performance. WARNING: Do not trim wet grass or foliage of small trees Keep hands away from blades. • • CAUTION: Smear the blade before and once per hour during •...
- Page 20 Makita Corporation Anjo, Aichi, Japan 884948-228...