Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
IMPORTANT NOTICE! Modification Required for Mounting your Router the universal phenolic mounting board that is included with the model t10432 does not have pre-drilled mounting holes to hold your router. this is because different brand routers have different base mounting hole configurations.
Bellingham, WA 98227-2069 Email: manuals@grizzly.com Router table Description the model t10432 router table includes a sturdy, all-steel stand. the large split-fence boards are adjustable from side to side with a rear-mounted dust port that connects to a shop vacuum or dust collection system.
Extended exposure to this noise without hearing protection can cause permanent hearing loss. MENTAL ALERTNESS. Be mentally alert when running machinery. Never operate under the influence of drugs or alcohol, when tired, or when distracted. model t10432 (mfg. since 11/10)
Always consider safety first, as it applies to your individual working conditions. Use this router table and other machinery with caution and respect. failure to do so could result in serious personal injury, damage to equipment, or poor work results. model t10432 (mfg. since 11/10)
Keep children and pets away from plastic bags or packing materials unpacked with this machine. Discard immediately. model t10432 (mfg. since 11/10) Needed for Setup the following are needed to complete the setup process, but are not included with your router table.
Brace figure 3. stand legs and short top stand braces attached. model t10432 (mfg. since 11/10) attach the long bottom stand braces to the legs with (8) m8-1.25 x 10 carriage bolts, 8mm flat washers, and m8-1.25 hex nuts, as shown in figure 4.
(mfg. since 11/10) make marks on the base and the router to guide you when mounting the router so that it will correctly face the front of the router table.
(see figure 14) until the ends of the straightedge lay flat on the table surface at all positions of the star pattern. figure 14. using the straightedge on the mounting board and table. model t10432 (mfg. since 11/10) Mounting Board Straightedge set screw...
Regardless of the content in this section, grizzly industrial will not be held liable for accidents caused by lack of training. model t10432 (mfg. since 11/10) To complete a typical operation, the operator...
(see the illustration in figure 16). important: To reduce the risk of kickback, do not take more than ⁄ " off for any one pass. model t10432 (mfg. since 11/10) Top View Shim Outfeed Straightedge Fence Board figure 16.
3, as illustrated in figure 20. Note: Make the outline as close as possible to the router bit and spindle without interfer- ing with rotation. Mounting Fastener Zero-Clearance Fence Table Cutter figure 20. example of a zero-clearance fence. model t10432 (mfg. since 11/10)
Check for proper clearance, connect the router to power, then make a test cut to verify the results. model t10432 (mfg. since 11/10) Free-Hand Routing irregular or free-hand routing, as illustrated in figure 21, takes a high degree of skill and dexter- ity and is done without the protection and aid from the fence and guard.
Worn or damaged router cords and plugs. • any other condition that could hamper the safe operation of this router table. model t10432 (mfg. since 11/10) maintenance. Frequently vacuum sawdust and wood chips from the table and router, then blow off the remain- ing dust with compressed air.
PHLP HD SCR 10- 24 X 2-1/4 DUST PORT KNOB 1/4-20 MITER SLOT TRACK HEX BOLT 1/4-20 X 3/4 TAP SCREW #4 X 1/2 FENCE GUARD HEX BOLT 5/16-18 X 1-1/2 KNOB 5/16-18 SCALE FLAT WASHER 1/4 model t10432 (mfg. since 11/10)
TAP SCREW #4 X 1/2 PN05 HEX NUT 1/4-20 PT10432045 MITER SLOT TRACK 11-3/4" PSS02M SET SCREW M6-1 X 6 model t10432 (mfg. since 11/10) REF PART # DESCRIPTION PT10432047 INSERT W/GUIDE PIN 9 X 12 PT10432051 ID LABEL PT10432052...
Page 25
Do you think your machine represents a good value? Would you recommend Grizzly Industrial to a friend? Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than 3 times.
Page 26
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 28
Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...