11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses. 16 A.W.G. 50ft 16 A.W.G. 100ft 14 A.W.G. 200ft 12 A.W.G. 300ft G1028/G1029 Dust Collector...
STARTING. Make sure switch is in off posi- tion before plugging in. Additional Safety Instructions For Dust Collectors 1. This dust collector is to be used for wood dust collection only. DO NOT use this dust collec- tor to pick up liquids and metal scrap includ- ing, but not limited to, nails and filings.
Do not attempt to rewire the motor if the diagram is missing. Contact the appropriate service center for more information. A plug is not provided with the G1028. It will be necessary to purchase a standard 110V plug from your local hardware store. If you are rewiring for 220V, see Figure 1 for recommended 220V receptacle.
G1028/G1029 Dust Collector Under no circumstances should the grounding pin from any three-pronged plug be removed. If it will not fit the outlet, have the proper outlet installed by a qualified electrician.
Standard features for both dust collectors include a push button switch, cyclone collector, and two large filter/collection bags. The G1028 has a 1 HP motor which is pre-wired for 110/120V and a 4" intake port. Air movement is 610 cubic feet per minute with a static pressure of 5.51".
Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise filing a freight claim can be difficult. Caution: The G1028/G1029 is a heavy machine (G1028-116 lbs. shipping weight, G1029-140 lbs shipping weight). DO NOT over-exert yourself while unpacking or moving your machine –...
Site Considerations When placing the G1028 or G1029 Dust Collector in your shop, three major considerations should be addressed: working clearances, lighting and electrical, and circuit loading. Working Clearances: Be sure to allow your- self sufficient room to safely operate your machines in any foreseeable operation.
SECTION 4: ASSEMBLY Beginning Assembly Assembly of the G1028/G1029 is straightforward. We have organized the assembly process into steps. Please follow them in sequence. Caution: All die-cut metal parts have a sharp edge (called “flashing”) on them after they are formed.
" - 18 x Figure 6. Figure 6. Mounting brackets to base. G1028/G1029 Dust Collector The collector attaches to each support bracket. The inside of the collector is funnel shaped and directs the air around in a cyclone motion. Make ⁄...
Hook the top loop of the filter bag over the support bracket. Figure 9. Figure 9. Slip the collection bag over the top edge of the collector and pull the strap tight to secure. Figure 9. Figure 10. G1028/G1029 Dust Collector...
Slip the steel band around the bag and tight- en down. Figure 11. Figure 11. G1028/G1029 Dust Collector Inlet (G1029 Only) Press the two-to-one inlet onto the inlet cover flange. Figure 12. The inlet is secured to the col- lector body by a press-on fit.
-14- Set Up The G1028/G1029 dust collectors can be either operated as mobile or stationary units. There are advantages and disadvantages to both systems. The primary advantage of a mobile system is low expense of ducts and fittings.
G1028/G1029 Dust Collector Stationary The G1028/G1029 can be set up as a stationary unit with the addition of a fixed duct system to service more than one machine at a time. The pri- mary advantage of a stationary system is it elimi-...
If you connect the dust collector to more than one machine by way of a non-conducting branching duct system and blast gates, the system must still be grounded as mentioned above.
SECTION 7: MAINTENANCE General Periodic maintenance will ensure safe operation, long dust collector life, and low overall cost of operation. Routinely check the condition of the following items and repair or replace as necessary: Loose mounting bolts, collector body, outlet, and support bracket mounting bolts.
Washington location using the address in the Introduction. The specifications, drawings, and photographs illustrated in this manual represent the Model G1028/G1029 as supplied when the manual was prepared. However, due to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly.
WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 24
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why Grizzly • • • Call Today For A – Trusted, Proven and a Great Value! ® Is The Industry Leader! ® SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS...