Advertisement
Available languages
Available languages
Programming the room number related
to the address associated with long pres-
sure of button 2 (code 017).
To program the room number related to the
address associated with long pressure on
button 2 (by default empty), it is necessary:
enter code 017;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address associated
with short pressure of button 3 (code
030).
Button 3 on the intercom provides the possibil-
ity of activating only one service. In particular
the one activated by short pressure (<1 sec.).
In fact, long pressure (> 3 sec.) activates/
deactivates the exclusion of all ringtones.
The permitted values for the services that can
be activated are:
- addresses 001-200: call to another user
- addresses 201-210: call to concierge unit;
- addresses 211-220: actuator activation
- addresses 231-253: door lock release (with
handset on hook) or activation of the speech
channel (with handset off), without having
been called, of the door unit;
- address 255: deletion of previously entered
value.
To program the address associated with short
pressure on button 3 (by default empty), it is
necessary:
enter code 030;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room number related
to the address associated with short
pressure of button 3 (code 031).
If the short pressure is assigned the same
address with which the intercom is called
from outside, the service that is activated
is the intercom call within the same flat. In
order to correctly address this call, the room
number associated to the short pressure on
button 3 must be programmed with the room
number corresponding to the intercom/vid-
eointercom to be called. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
To program the room number related to the
address associated with short pressure on
button 3 (by default empty), it is necessary:
enter code 031;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address of the service
activated by closing contact A1/GN (code
018).
When the input terminals A1 and GN of the
intercom are closed by means of a button, the
floor call is activated (the intercom rings with
the melody programmed for this type of call,
without enabling the conversation). It is pos-
sible to associate an address to the input if, in
addition to receiving the floor call tone, one of
the services indicated below is to be activated:
- address 000: floor call relaunch to all apart-
ment stations having the same user address
of the intercom where A1 and GN are closed
together;
- addresses 001-200: floor call sent to another
user;
- addresses 201-210: send alarm to concierge
unit;
- address 255: delete previously entered value.
To program the address associated with clos-
ing contacts A1/GN (by default empty), it is
necessary to:
enter code 018;
press button
; o confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of the room number related
to the address of the service activated
by the closing of the A1/GN contact (code
019).
If the input A1/GN is assigned as address the
same address with which the intercom is
called from outside, the room number of the
apartment station to which the floor call will
be sent must be set. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
To program the room number relative to the
address of the service activated by the closing
of the A1/GN contact (by default empty) it is
necessary:
enter code 019;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming ringtones (codes 020 to
028).
The following parameters can be programmed
in relation to the ringtones. First dial the
code (020-028) and then the value to be set:
-code 020: code identifying the common vol-
ume level associated with all the ringtones
(factory value 3, permitted values from 1=min-
imum to 5=maximum);
-codes 021, 022, 023 and 024: the four codes
identify the ringtone set for calls from the
external door station, from intercom within
the same flat, from another flat and from the
floor respectively (see table 1 for the factory
settings;)
- codes 025, 026, 027 and 028: the four codes
identify the number of rings associated to the
ringtone set for calls from external door staion,
intercom inside the same flat, from another
flat and from floor respectively (for factory
settings see table 1, allowed values from 1 to 5).
To perform the desired programming it is
necessary:
enter one of the codes from 020 to 028;
press button
to confirm;
enter the new value to be assigned;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the activation time of the
office function (code 032).
The office function provides that, when the call
arrives, without pressing the button
before entering a conversation, after a certain
time interval (to be configured with code 032),
the lock connected to terminals S+/S- of the
external door station that made the call is
automatically opened. Allowed values are
from 0 to 29 seconds (where 0 indicates that
the function is disabled). The function is not
enabled by default. A long press on button
2 (>3 sec) enables/disables the office func-
tion. The operation of the office function is
indicated by the
icon LED flashing rapidly.
To set the time interval it is necessary to:
enter code 032;
press button
to confirm;
enter the new activation time; enter 255 to
erase a value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Return to factory defaults
To return to the factory settings, it is neces-
sary to:
enter programming mode following the
instructions described in the paragraph
"Entering programming mode",
press the following buttons in this se-
quence: 3, 2 ,1 and
;
the
icon LED stops flashing, the
LED lights up for one second and then the
icon LED returns to flashing slowly;
exit programming. If new programming is
required, re-enter and perform the neces-
sary steps.
Attention: returning to the factory
defaults has no effect on the user address,
which is set manually via the dip-switches
of SW1.
.
and
icon
Mi 2576
- 11 -
Advertisement
