Advertisement
Quick Links
Installation & Operations Manual : SZ Flip-Up Windshield, Polaris Mid-Size Pro-Fit Ranger
Installation Information:
This product does not require any modifications to your vehicle. Please familiarize yourself with all the steps before
beginning assembly.
Seizmik makes Windshields, Mirrors, Door Kits, Light Bars, Hood Racks, and other great accessories for UTV's to
maximize the vehicles usefulness. To help you do what you do better.
If you have any questions, comments, need assistance, or are missing parts, please visit our website
http://seizmik.com/customer-support
information on our product or call 1-866-838-3366 between 9:00AM and 5:00PM EST.
Parts List:
1.
50-50222 MS Ranger Windshield
2.
54-91033 Gasket
3.
54-96020 Vent Pair
4.
54-96049 Tube Assembly
5.
54-96061 Brace Mounting Block Cover
6.
54-96065 T Handle
7.
54-96073 Badge
8.
54-96058 Shim (2)
9.
54-96080 Ball Bracket, Driver
10.
54-96081 Ball Bracket, Passenger
11.
54-96086 Gas Spring (2)
12.
54-96071 Center Retainer
13.
54-96072 Rub Plate
14.
54-96089 Strike Plate, Driver
15.
54-96090 Strike Plate, Passenger
16.
54-96085 Hinge Half, Upper (2)
17.
54-96084 Hinge Half, Lower (2)
18.
54-96054 Ball Stud Clamp (2)
19.
54-96053 MS Ranger Hardware Bag
Installation Video
Scan code with your phone's
camera and follow the link
Or email us at service@seizmik.com. Visit
Part Number 50-50222KIT
www.seizmik.com
Tools Needed:
•
4mm, 5mm, 6mm Allen Wrenches
•
10mm, 12mm, 13mm Open End Wrenches
•
Socket Wrench with 13mm Socket
•
Small Flathead Screwdriver
•
T40 Torx Socket
for more
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Seizmik 50-50222KIT
Summary of Contents for Seizmik 50-50222KIT
- Page 1 This product does not require any modifications to your vehicle. Please familiarize yourself with all the steps before beginning assembly. Seizmik makes Windshields, Mirrors, Door Kits, Light Bars, Hood Racks, and other great accessories for UTV’s to maximize the vehicles usefulness. To help you do what you do better.
- Page 2 Parts Brace Mounting Block Small Mounting Block End Mounting Block...
- Page 3 Hardware In Tube Assembly: Brace Mounting Block Small Mounting Block End Mounting Block M6x45 Button Head M6x40 Button Head M6 Nylon Lock Nut M6x50 Button Head In Hardware Bag: M8x16 Button Head M8x50 Button Head M8x30 Socket Head M6x18 Button Head M6x30 Button Head M6 Flange Nylon Lock Nut M8 Jam Nut...
- Page 4 Place the windshield down on a large flat surface with Take the Ball Brackets (9 & 10) and orient them on something under it to prevent scratching. It should be the inside of the windshield as shown. Shown above oriented with Vent Pair lever-side up and Gasket is Ball Bracket, Driver (9).
- Page 5 Place the Tube assembly on the inside of the Insert two M6x45 Button Head Bolts through the Badge (7), through the windshield, and then through windshield with the pockets for captive nuts in each of the Brace Mounting Block. Put the outer two M6 the mounting blocks facing upwards.
- Page 6 There is a gap for the Shim to be snapped in place Remove the two M8 ball studs from each Gas Spring. over the M6x50mm Button Head Bolt in between the There will be 4 total ball studs. Do this by prying up End Mounting Block and the Ball Bracket.
- Page 7 Now install the Center Retainer on the inside of the Now attach each Hinge Half, Lower to the outer side windshield using 2 - M6x30 Button Head Bolts and 2 - of the windshield with the angle coming away from the M6 Nylon Lock Nuts.
- Page 8 Thread one M8 Ball Stud into each Ball Stud Clamp Attach the Ball Stud Clamp to the vehicle frame by loosening it’s two M8x30 Socket Head Bolts until able to fit clamp over the tubing. Space the Ball Stud Clamp from the Strike Plate so that its bottom edge is 13.0 inches away from the top edge of the strike plate.
- Page 9 Shown above is both assembled Hinge Halves, Upper Use a 5mm hex and a 13mm socket wrench to loosely and their orientations on the frame of the vehicle. fasten two M8x16mm button head bolts and two M8 Nylon Lock Nuts for each Hinge Half, Upper on each side of the vehicle.
- Page 10 Check the alignment of the windshield. These two Press the bottom corners of the windshield in gently to *do not slam the bolts on either side of the windshield can be loosened latch the strikers in the Strike Plates. windshield closed yet * to allow for adjustment of the windshield alignment.
- Page 11 This piece of the Rub Plate has two orientations. If the With the windshield held open, install the Rub Plate, bracket isn’t tight enough, flip this piece 180° and from inside the vehicle, by sliding the hooked piece tighten. under the center retainer and then fastening to the piece shown in the next step.
- Page 12 Repeat this process for the smaller diameter end of To Close: With the windshield open, pull the T Handle swiftly and in a straight line towards you to engage the Gas Spring. Install this end’s clip over the ball the strikers in the strike plates and close the stud near the End Mounting Block on the Tube windshield.
Need help?
Do you have a question about the 50-50222KIT and is the answer not in the manual?
Questions and answers