Advertisement
Quick Links
RZR PRO XP 2 Seat Seizmik Skid Plate Manual
Part # 76-10167
Always observe the warnings and precautions in this manual when using your Seizmik products. For best results, carefully
follow the instructions in this manual and make no modifications.
If you have any questions, comments, need assistance, or are missing parts, please call 1-866-838-3366 between 9:00AM
and 5:00PM EST. You can email us at
support@seizmik.com
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Seizmik RZR PRO XP
Summary of Contents for Seizmik RZR PRO XP
- Page 1 RZR PRO XP 2 Seat Seizmik Skid Plate Manual Part # 76-10167 Always observe the warnings and precautions in this manual when using your Seizmik products. For best results, carefully follow the instructions in this manual and make no modifications.
- Page 2 View looking up at the underside of the vehicle Front Rear...
-
Page 3: Parts List
Parts List 76-10183 76-10184 76-10185 76-10186 76-10187 76-10188 76-10189 76-10190 76-10191 99-10001 99-10002 99-10003 99-10006 99-10005 1.5” Wrap Around Clamp M6 Clip Nut 2.0” Wrap Around Clamp Tapered Hex Screw M6x25mm Skid Plate Washer 1.75” Snap Over Clamp Skid Plate Insert Washer... - Page 4 ALL GREEN holes use M6x25mm tapered bolt and washer Into factory threaded holes unless called out otherwise. Snap over Wrap around BLUE holes use M6x40mm with wrap around clamp or M6x16mm with snap over clamp. (Next page specifies clamp locations) ALL YELLOW holes use M6x25mm tapered bolt and washer into clip nuts attached to metal brackets unless called out otherwise.
- Page 5 M8x16mm bolt Uses OEM Threaded holes Uses Clamps Threads into brackets with clip nuts Uses insert washer or nut Self Tapping Screws-May or may not require predrilling of 1/8” pilot hole...
- Page 6 Uses OEM Threaded holes Uses Clamps Threads into brackets with clip nuts Uses insert washer or nut Self Tapping Screws-May or may not require predrilling of 1/8” pilot hole...
- Page 7 Attach all clip nuts to specified holes in metal brackets. Threading should face upwards, toward vehicle.
- Page 8 Attach bash plate to front panel Thread the two M8x16mm bolts through the bash plate and into the front panel Attach clamp to side panels Thread M6x16mm bolts through the side panels and into the snap over clamps...
- Page 9 This side of insert washer faces upward, toward vehicle. To start, remove stock skid plate. Then, snap clamps around chassis in general locations shown (Shown in BLUE). The threading on the clamps should face outward. Place insert washers in Sheetmetal holes in vehicle (Shown in ORANGE).
- Page 10 M6x25mm Tapered Bolt To start, loosely install the center 3 bolts and washers (Shown in GREEN) so that the middle panel is held in place on its own. Next, loosely attach the metal brackets to the middle panel using 4 bolts and washers (Shown in YELLOW) into the clip nuts that you attached to the metal brackets.
- Page 11 M6x25mm Tapered Bolt 1.5” Wrap Around Clamp M6x30mm Bolt M6x30mm Bolt Loosely install the bolts and washers (Shown in GREEN) so that the rear panel is held in place on its own. Place the rear spacer between the rear panel and the vehicle underbody.
- Page 12 M6x30mm Bolt and Insert washer M6x25mm Tapered Bolt Slide bash plate onto front piece of Sheetmetal (as shown), loosely install two bolts and washers (Shown in GREEN). Install M6x30mm bolt into insert washer (Shown in ORANGE). Bash Plate attached to Sheetmetal...
- Page 13 2.0” Wrap Around Clamp M6x35mm Bolt M6x35mm Bolt M6x25mm Tapered Bolt Self Tapping Screw M6x25mm Tapered Bolt Snap the snap over clamp (pg. 8) onto the tubing and then loosely install all tapered bolts and washer (Shown in GREEN). Then install M6x35mm bolts and washer (Shown in BLUE) and bolts and washers into clip nuts (Shown in YELLOW).
Need help?
Do you have a question about the RZR PRO XP and is the answer not in the manual?
Questions and answers