Installation; Installation Terminals; Configuration Switches - golmar Art 4 LITE/G2+ User Manual

MONITOR ART 4

INSTALLATION

Avoid dusty or smoky environments or locations near sources of heat.
For proper installation, use the template supplied with the product.
1. Position the top of the template at a height of 1.65m.
2. If you are going to use an embedding box to pass the wiring through, make sure that it is in line with the holes
corresponding to the box model chosen and fix the connector. If you prefer to fix the connector directly to the
wall, make four 6mm holes at the points indicated (A), insert the wall plugs supplied and screw in the connector.
3. Pass the installation wires through the middle hole and connect them to the removable terminals as shown in the
wiring diagrams. Before connecting the removable terminals to the monitor, configure the switch as indicated below.
4. Connect the removable terminals to the monitor and place the monitor in front of the connector, making sure the
fixings line up. Move the monitor downwards to secure it.
INSTALLATION TERMINALS (J)
For ease of installation, the installation terminals are removable and supplied in a separate bag. Once the
terminals are wired, place them in position.
SA
GND
HZ
HZ
BUS
BUS
Note: HZ push button function mode: When HZ push button is pressed will be call tone and activate the output of
auxiliary call repeater with standby monitor call process
process and "Do not disturb" mode Important: Up to 6 monitors/ apartments with push button "HZ"
intercom
activated at the same time (with system and monitors in standby).
CONFIGURATION SWITCHES (I)
ART4 LITE/G2+ monitor with V.01 (addresses 1 to 32):
Switches 1 to 5: Sets the monitor address (addresses to 3 ).
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Important: Apartment 1 (Dip1 to ON & Dip2-Dip5 to OFF).
Important: Apartment 32 (Dip1 - Dip5 to OFF)
Switches 6 & : These define whether the monitor is master or slave. Each apartment must have one master 7
monitor, and only one.
Master
ON
1 2 3 4 5
Switch 8: This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable ends.
Deactivate it only in intermediate monitors.
ART4 LITE/G2+ monitor with V.02 and next (addresses 1 to 128):
Switches to 7 1 :
The switches set to OFF have a zero value. The values of the switches set to ON are shown in the table below. The
monitor code is the sum of the values of the switches set to ON.
Important: Apartment 1 (Dip1 to ON & Dip2-Dip7 to OFF)
Important: Apartment 128 (Dip1 - Dip7 to OFF).
Switch 8: This activates the end-of-line resistance in the ON position. Activate it in monitors where the bus cable
ends. Deactivate it only in intermediate monitors.
To define whether the monitor is master or slave:
To define whether the monitor is master or slave (see special codes page 21 to 23). Each apartment must have one
master monitor, and only one.
LITE /G2+
BUS, BUS: Communication BUS (non-polarised).
SA, GND: Auxiliary call repeater output (max 50mA/12V), relay SAR-12/24.
HZ, HZ: Apartment front door button input:
Connect only on the master monitor. The signal received is then transmitted
to the slave monitors in the same apartment through the BUS.
Slave 1
ON
6 7 8 1 2 3
Sets the monitor address (addresses
, , com unic m
.
1 2
Table of values
Switch number:
Val ue when ON:1
ON
4 5 6 7 8 1
1 to 1 8 2 ).
Table of values
Switch number
Value when ON
ation process HZ tone with lower audio level (
1 2 3 4 5
2 4 8 16
Example: 0+ 0+4+0+ 16= 20
Slave 2
2 3 4 5 6 7 8
: 1 2 3 4 5 6 7
: 1 2 4 8 16 32 64
E mpl : 0+ 0+4+0+ 16+ xa
5
),
ON
1 2 3 4 5 6 7 8
Slave 3
ON
1 2 3 4 5 6 7 8
ON
1 2 3 4 5 6 7 8
e 0+0 = 20