EWM Phoenix 355 Progress puls HP MM TKM Operating Instructions Manual page 5

5.10 PC interface ......................................................................................................................... 84
5.10.1
5.11 Special parameters (advanced settings) ............................................................................. 84
5.11.1
5.11.2
5.11.3
5.12 Machine configuration menu ................................................................................................ 96
5.12.1
5.13 Power-saving mode (Standby) ............................................................................................ 98
6 Maintenance, care and disposal ................................................................................................. 99
6.1 General ................................................................................................................................ 99
6.2 Explanation of icons ........................................................................................................... 100
6.3 Maintenance schedule ....................................................................................................... 101
6.4 Disposing of equipment ..................................................................................................... 102
7 Rectifying faults ......................................................................................................................... 103
7.1 Error messages (power source) ........................................................................................ 103
7.2 Checklist for rectifying faults .............................................................................................. 105
7.3 Vent coolant circuit ............................................................................................................. 106
7.4 Resetting JOBs (welding tasks) to the factory settings ..................................................... 107
7.4.1
7.4.2
8 Technical data ............................................................................................................................ 108
8.1 Phoenix 355 Progress puls MM TKM ................................................................................ 108
9 Accessories ................................................................................................................................ 109
9.1 Welding torch cooling system ............................................................................................ 109
099-005403-EW501
10.2.2022
Connection ........................................................................................................... 84
Selecting, changing and saving parameters ........................................................ 85
Reset to factory settings ....................................................................................... 87
Special parameters in detail ................................................................................. 87
5.11.3.1 Ramp time for wire inching (P1) ............................................................ 87
5.11.3.2 Program "0", releasing the program block (P2) .................................... 88
5.11.3.3 Display mode for Up/Down welding torch with one-digit 7-segment
display (P3) ........................................................................................... 88
5.11.3.4 Program limit (P4) ................................................................................. 88
5.11.3.5 Special cycle in the operating modes special latched and non-latched
(P5)........................................................................................................ 88
5.11.3.6 Correction operation, threshold value setting (P7) ............................... 89
5.11.3.7 Switching programs with the standard torch trigger (P8) ...................... 90
5.11.3.8 Latched/special-latched tap start (P9) .................................................. 91
5.11.3.9 "Single or dual operation" (P10) setting ................................................ 91
5.11.3.10 Latched special tapping time setting (P11) ........................................... 91
5.11.3.11 JOB list switching (P12) ........................................................................ 92
5.11.3.12 Lower and upper limits of the remote JOB changeover process (P13,
P14) ....................................................................................................... 93
5.11.3.13 Hold function (P15) ............................................................................... 93
5.11.3.14 Block JOB mode (P16) ......................................................................... 93
5.11.3.15 Selecting programs with the standard torch trigger (P17) .................... 94
5.11.3.16 Switching the operating mode and welding type using the wire feed
control (P18) .......................................................................................... 94
5.11.3.17 Mean value display for superPuls (P19) ............................................... 94
5.11.3.18 Predefined execution of the pulsed arc welding process in the PA
program (P20) ....................................................................................... 94
5.11.3.19 Predefined absolute value for relative programs (P21) ........................ 94
5.11.3.20 Electronic gas flow control, type (P22) .................................................. 94
5.11.3.21 Program settings for relative programs (P23) ....................................... 94
5.11.3.22 Correction or nominal voltage display (P24) ......................................... 95
5.11.3.23 JOB selection in Expert mode (P25) ..................................................... 95
5.11.3.24 Nominal value wire heater (P26) ........................................................... 95
5.11.3.25 Mode switching at welding start (P27) .................................................. 95
5.11.3.26 Error threshold electronic gas flow control (P28) .................................. 95
5.11.3.27 Units system (P29) ................................................................................ 95
5.11.3.28 Selection option - Program sequence with welding power rotary knob
(P30) ..................................................................................................... 95
Aligning the cable resistance ................................................................................ 97
Resetting a single JOB ....................................................................................... 107
Resetting all JOBs .............................................................................................. 107
Notes on using these operating instructions
Contents
5