EWM Phoenix 355 Progress puls HP MM TKM Operating Instructions Manual page 4

Table of Contents

Advertisement

Contents
Notes on using these operating instructions
5.3.8
5.3.9
5.3.10
5.3.11
5.3.12
5.3.13
5.3.14
5.3.15
5.3.16
5.3.17
5.4
MMA welding ........................................................................................................................ 71
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.4.6
5.4.7
5.5
TIG welding .......................................................................................................................... 74
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.5.6
5.5.7
5.6
Access control ...................................................................................................................... 80
5.7
Remote control ..................................................................................................................... 81
5.8
Power-saving mode (Standby) ............................................................................................. 81
5.9
Interfaces for automation ..................................................................................................... 81
5.9.1
5.9.2
5.9.3
5.9.4
4
5.3.7.1
Accessory components for operating point setting ............................... 44
5.3.7.2
Arc length .............................................................................................. 44
5.3.7.3
Arc dynamics (choke effect) .................................................................. 44
5.3.7.4
superPuls .............................................................................................. 44
5.3.7.5
Burn-back .............................................................................................. 45
Conventional MIG/MAG Welding (GMAW non synergic) ..................................... 46
5.3.8.1
Setting the operating point (welding output).......................................... 46
Welding power (operating point) ........................................................................... 47
5.3.9.1
feed speed ............................................................................................. 47
5.3.9.2
Arc length .............................................................................................. 47
5.3.9.3
Accessory components for operating point setting ............................... 47
forceArc / forceArc puls ........................................................................................ 48
rootArc/rootArc puls .............................................................................................. 48
Operating modes (functional sequences) ............................................................. 49
5.3.12.1 Explanation of signs and functions ........................................................ 49
5.3.12.2 Automatic cut-out .................................................................................. 49
MIG/MAG program sequence ("Program steps" mode) ....................................... 62
5.3.13.1 Selection of the program sequence parameter ..................................... 62
5.3.13.2 MIG/MAG overview of parameters ........................................................ 63
5.3.13.3 Example, tack welding (non-latched) .................................................... 63
5.3.13.5 Example, aluminium welding (latched special) ..................................... 65
5.3.13.6 Example, visible seams (latched super pulse) ...................................... 66
Main program A mode .......................................................................................... 67
5.3.14.1 Selecting parameters (program A) ........................................................ 68
Standard MIG/MAG torch ..................................................................................... 69
MIG/MAG special-torches ..................................................................................... 69
5.3.16.1 Program and up/down operation ........................................................... 69
Expert menu (MIG/MAG) ...................................................................................... 70
5.3.17.1 Selection ................................................................................................ 70
5.3.17.2 Programme limit .................................................................................... 71
Connecting the electrode holder and workpiece lead .......................................... 71
Welding task selection .......................................................................................... 72
Welding current setting ......................................................................................... 72
Arcforce ................................................................................................................. 72
Hotstart ................................................................................................................. 73
Antistick ................................................................................................................. 73
Parameter overview .............................................................................................. 73
Preparing the TIG welding torch ........................................................................... 74
Welding torch and workpiece line connection ...................................................... 74
Welding task selection .......................................................................................... 74
Welding current setting ......................................................................................... 75
Arc ignition ............................................................................................................ 75
5.5.5.1
Liftarc ..................................................................................................... 75
Operating modes (functional sequences) ............................................................. 76
5.5.6.1
Explanation of signs and functions ........................................................ 76
5.5.6.2
Automatic cut-out .................................................................................. 76
TIG program sequence ("Program steps" mode) ................................................. 80
Automation interface ............................................................................................. 82
Remote control connection socket, 19-pole ......................................................... 83
RINT X12 robot interface ...................................................................................... 83
BUSINT X11 industrial bus interface .................................................................... 83
099-005403-EW501
10.2.2022

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Phoenix 355 Progress puls HP MM TKM and is the answer not in the manual?

Subscribe to Our Youtube Channel

Table of Contents