Mounting With Standard Kits - Norseman XGB Series Installation, Operation & Maintenance Instructions Manual

C.3 Mounting with Standard Kits
1. Ceiling Mounting

3.3 MOUNTING WITH STANDARD KITS

1.1 Install the ceiling bracket to the mounting surface
3.3 MOUNTING WITH STANDARD KITS
3.3.1 CEILING MOUNTING with the desired orientation. Ensure that 'LINE A"
(Figure 4, page 6), a line drawn perpendicular
ted 3.3.1 CEILING MOUNTING
a) Install the ceiling bracket to the mounting surface with the desired
to the bolt holes in the mounting bar, is pointed in
ing
orientation. Ensure that 'LINE A" (Figure 3), a line drawn
the desired direction of airflow. The ceiling bracket
ing a) Install the ceiling bracket to the mounting surface with the desired
perpendicular to the bolt holes in the mounting bar, is pointed in the
must be secured to the mounting surface using as
ater orientation. Ensure that 'LINE A" (Figure 3), a line drawn
desired direction of airflow. The ceiling bracket must be secured to
many as six (but not less than two) 5/8" fasteners
perpendicular to the bolt holes in the mounting bar, is pointed in the
the mounting surface using as many as six (but not less than two)
desired direction of airflow. The ceiling bracket must be secured to (not provided). Make certain that lockwashers are
5/8" fasteners (not provided). Make certain that lockwashers are
ide the mounting surface using as many as six (but not less than two)
used under all nuts or lag bolts.
used under all nuts or lag bolts.
d at 5/8" fasteners (not provided). Make certain that lockwashers are
cm used under all nuts or lag bolts.
1.2 Hoist the heater up to the ceiling bracket. Line up
b) Hoist the heater up to the ceiling bracket. Line up the large centre
the large centre hole in the swivel bracket with the
hole in the swivel bracket with the large hole in the mounting bar.
nto b) Hoist the heater up to the ceiling bracket. Line up the large centre
large hole in the mounting bar.
hole in the swivel bracket with the large hole in the mounting bar.
c) Insert the 1/2" bolt and loosely secure with nut and washers
1.3 Insert the 1/2" bolt and loosely secure with nut and
provided. Tilt the heater at the desired angle to the horizontal and
be c) Insert the 1/2" bolt and loosely secure with nut and washers
washers provided. Tilt the heater at the desired
secure with the 3/8" bolt. Tighten the 1/2" bolt.
ged provided. Tilt the heater at the desired angle to the horizontal and
angle to the horizontal and secure with the 3/8"
n if secure with the 3/8" bolt. Tighten the 1/2" bolt.
bolt. Tighten the 1/2" bolt.
ater
ion
n is
ate
CEILING BRACKET
CEILING BRACKET
MOUNTING BAR
MOUNTING BAR
3/8" Flat Washer, Lock Washer, Nut
.
3/8" Flat Washer, Lock Washer, Nut
sing.
1/2" Flat Washer, Lock Washer, Nut
1/2" Flat Washer, Lock Washer, Nut
skid
the
Figure 4 – Ceiling Mounting
Figure 3 - Ceiling Mounting
Figure 3 - Ceiling Mounting
6
2.
3.3.2 WALL MOUNTING
3.3.2 WALL MOUNTING
a) Install the ceiling bracket to the wall bracket with the desired
orientation. Ensure that "LINE A" (Figure 4), a line drawn
a) Install the ceiling bracket to the wall bracket with the desired
perpendicular to the bolt holes in the mounting bar, is pointed in the
orientation. Ensure that "LINE A" (Figure 4), a line drawn
desired direction of air flow. Secure the wall bracket to the mounting
perpendicular to the bolt holes in the mounting bar, is pointed in the
surface. The wall bracket must be secured to the mounting surface
desired direction of air flow. Secure the wall bracket to the mounting
using as many as six (but not less than four) 5/8" fasteners (not
surface. The wall bracket must be secured to the mounting surface
provided). Make certain that lockwashers are used under all nuts or
using as many as six (but not less than four) 5/8" fasteners (not
lag bolts.
provided). Make certain that lockwashers are used under all nuts or
lag bolts.
b) Follow steps b) and c) outlined in 3.3.1.
b) Follow steps b) and c) outlined in 3.3.1.
MOUNTING SURFACE
MOUNTING SURFACE
11/16" Dia. Mounting Holes
11/16" Dia. Mounting Holes
3/8" bolt
3/8" bolt
1/2" bolt
1/2" bolt
SWIVEL MOUNTING BRACKET
SWIVEL MOUNTING BRACKET
SWIVEL MOUNTING BRACKET
SWIVEL MOUNTING BRACKET
Figure 5 – Wall Mounting
Figure 4 - Wall Mounting
Figure 4 - Wall Mounting
Wall Mounting
2.1 Install the ceiling bracket to the wall bracket
with the desired orientation. Ensure that "LINE A"
(Figure 5, page 6), a line drawn perpendicular
to the bolt holes in the mounting bar, is pointed
in the desired direction of air flow. Secure the wall
bracket to the mounting surface. The wall bracket
must be secured to the mounting surface using as
many as six (but not less than four) 5/8" fasteners
(not provided). Make certain that lockwashers are
used under all nuts or lag bolts.
2.2 Follow steps 1.2 and 1.3 outlined in Ceiling
Mounting, page 6.
MOUNTING SURFACE
11/16" dia. mounting holes
MOUNTING SURFACE
11/16" dia. mounting holes
5/8" flatwasher, lockwasher, nut
5/8" flatwasher, lockwasher, nut
WALL BRACKET
5/8" Bolt
5/8" Bolt
3/8" Bolt
3/8" Bolt
1/2" Bolt
1/2" Bolt
WALL BRACKET
CEILING BRACKET
CEILING BRACKET
5/8" Bolt
5/8" Bolt
MOUNTING BAR
MOUNTING BAR
3/8" flatwasher, lockwasher, nut
3/8" flatwasher, lockwasher, nut
1/2" flatwasher, lockwasher, nut
1/2" flatwasher, lockwasher, nut
3.3
a)
orie
per
des
the
loc
b)
Fig