Table of Contents
Advertisement
Quick Links
Solo Encore
Installation Guide
For Model:
SOE54
WARNING:
DC Motor will not
operate until blades
are installed
net weight of fan: 11.24 lb (5.10 kg)
READ THESE INSTRUCTIONS AND
SAVE THEM FOR FUTURE USE
Table of Contents:
Safety Tips. pg. 1
Unpacking Your Fan. pg. 2
Parts Inventory. pg. 2
Installation Preparation. pg. 3
Hanging Bracket Installation. pg. 3
Fan Assembly. pgs. 4 - 5
Wiring. pg. 6
Canopy Assembly. pg. 7
Blade Assembly. pg. 7
Remote/Wall Control Operation. pg. 11
Testing Your Fan. pg. 11
Troubleshooting. pg. 12
Warranty. pg. 12
Parts Replacement. pg. 12
PRINTED IN CHINA
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Craftmade Solo Encore SOE54
Summary of Contents for Craftmade Solo Encore SOE54
-
Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Solo Encore Installation Guide For Model: Table of Contents: SOE54 Safety Tips. pg. 1 Unpacking Your Fan. pg. 2 Parts Inventory. pg. 2 Installation Preparation. pg. 3 Hanging Bracket Installation. pg. 3 Fan Assembly. -
Page 2: Safety Tips
SAFETY TIPS. WARNING: To reduce the risk of electrical shock, turn off the electricity to the fan at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. READ ALL INSTRUCTIONS AND SAFETY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS. -
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs. -
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet that the hanging location allows the blades a (2.13 m) (76 cm) clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft. -
Page 5: Fan Assembly. Pgs
5. Fan Assembly. stop pin Remove hanging ball from downrod provided by set screw loosening set screw on hanging ball. Remove pin and clip. Lower hanging ball and remove stop pin. Slide hanging ball off of the downrod. [Refer to hanging ball diagram 1.] clip... - Page 6 5. Fan Assembly. (cont.) With the hanging bracket secured to the outlet box and able to support the fan, you are now wood ceiling ready to hang your fan. Grab the fan firmly with joist two hands. Slide downrod through opening in safety cable loop hanging bracket and let hanging ball rest on the hanging bracket.
-
Page 7: Wiring
6. Wiring. white supply wire WARNING: Turn off circuit breakers to current fixture from breaker panel and be sure operating black supply wire ground light switch is turned to the OFF position. (green or bare) CAUTION: Be sure outlet box is properly grounded or from ceiling that a ground wire (GREEN or Bare) is present. -
Page 8: Canopy Assembly
7. Canopy Assembly. hanging bracket Locate 2 screws on underside of hanging bracket and remove screw closest to the open end of the screw hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. Place rounded part of slotted hole in canopy over loosened screw in hanging bracket and push up. - Page 9 9. Light Kit Assembly (Optional). (cont.) motor housing If you wish to use the light kit, remove 3 screws from fitter plate and save them for later use. fitter plate Remove the Ground screw (labeled) from the fitter plate and attach the YELLOW/GREEN wire from the LED light kit.
-
Page 10: Handheld Remote Control Assembly
10. Handheld Remote Control Assembly. IN ORDER TO USE THE HANDHELD REMOTE remote CONTROL, PLEASE CONTINUE WITH SECTION 10 for control remote control assembly instructions. If you have cover already installed the wall control but do not wish to use the handheld remote control, please proceed to Section 11. -
Page 11: Automated Learning Process./Activating Code
11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control wall control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position. -
Page 12: Remote/Wall Control Operation
12. Remote/Wall Control Operation. handheld wall control remote control IMPORTANT: Handheld remote control and wall III IV control must be SYNCHRONIZED with fan in order to properly function. Fan SPEED control buttons--1: Use to control the ceiling fan speed 1-6 Fan OFF button--2: Use to turn the fan off REVERSE function button--3:... -
Page 13: Troubleshooting
Service at 1-800-486-4892 to arrange for return of fan. 3. Check to be sure fan is wired properly. Return fan, shipping prepaid, to Craftmade. We will repair 4. Learning process between fan, handheld remote or ship you a replacement fan, and we will pay the return control and, if applicable, wall control may not have been shipping cost.
Need help?
Do you have a question about the Solo Encore SOE54 and is the answer not in the manual?
Questions and answers