Stiga MP1 500 Li D48 Series Operator's Manual page 27

7.3 CLEANING
Clean thoroughly following the instructions
below every time it is used.
7.3.1 Cleaning the machine
• Always make sure the air intakes are free of debris.
• Do not spray water onto the motor and electrical
components, prevent them from getting wet (Fig.24).
• Do not use aggressive liquids to clean the chassis.
• To reduce fire hazards, keep the lawnmower
and, in particular, the motor free of grass,
leaves, or excessive grease.
• Always keep the levers, display and
buttons free of debris.
7.3.2 Cleaning the cutting means assembly
Remove grass debris and mud accumulated in
the chassis to prevent it from drying and causing
problems the next time the lawnmower is used.
Tilt the machine laterally and make sure that
it is stable before starting any work.
For side discharge: remove the discharge
chute (if mounted - par. 6.1.2d.).
The paintwork of the internal part of the chassis may
crack off over time due to the abrasive action of the cut
grass; In this case, take immediate action by retouching
the paintwork with rust-preventive paint, to prevent
the formation of rust which may corrode the metal.
7.3.3 Cleaning the grass catcher
1. Empty the grass catcher.
2. Shake it to remove grass cuttings and soil residue.
Wash it, rinse it and fit it back so as
3.
to facilitate quick drying.
7.4 NUTS AND BOLTS
Keep all nuts, bolts and screws tight to be sure
the equipment is in a safe working condition.
8. OCCASIONAL MAINTENANCE
Before commencing any inspections, cleaning or
maintenance/adjustments on the machine:
• Stop the machine.
• Remove the safety key, (never leave the key inserted or
within the reach of children or unauthorised persons).
• Make sure that all moving parts have
come to a complete stop.
• Allow the motor to cool before storing
in an enclosed space.
• Read the relevant instructions.
• Use suitable clothing, protective gloves and goggles.
8.1 CUTTING MEANS
An improperly sharpened cutting means pulls at
the grass and causes the lawn to turn yellow.
Do not touch the cutting means until the key has
been removed and the cutting means is completely sta-
tionary.
All work on the cutting means (disassembly,
sharpening, balancing, repairing, reassembly and/or re-
placing) are demanding jobs that require special skills
as well as special tools; For safety reasons, these jobs
are best carried out at a Authorised Service Centre.
Make sure damaged, misshapen or worn cutting
means are replaced, together with the securing screws,
to preserve balance.
IMPORTANT Always use original cutting means
bearing the code indicated in the "Technical Data".
Given product evolution, the cutting means
listed in the "Technical Data" table may be
replaced in time with others having similar
interchangeable and operating safety features.
9. STORAGE
9.1 STORING THE MACHINE
When the machine is to be stored away:
1. Wait for the engine to cool.
2. Remove the safety key.
3. Remove the batteries from their hous-
ing and recharge them (par 7.2.2).
4. Clean (par. 7.3).
Check there are no loose or damaged compo-
5.
nents. If necessary, replace the damaged com-
ponents and tighten any screws and loose bolts
or contact the authorised service centre.
6. Store the machine (Fig.29):
• In a dry place.
• Protected from inclement weather.
• Covered with a sheet where possible.
• In a place where children cannot get to it.
• Making sure that keys or tools used for
maintenance are removed.
9.2 STORING THE BATTERY
The battery must be kept in a cool,
shaded place without humidity.
NOTE If case of prolonged periods of inactivity, recharge
the battery every two months to prolong its service life.
10. HANDLING AND TRANSPORTATION
Whenever the machine is to be handled,
raised, transported or tilted you must:
– Stop the machine (par. 6.5).
– Remove the safety key.
– Make sure that all moving parts have
come to a complete stop.
– Wear heavy duty gloves.
– Hold the machine in the points offering a safe grip,
taking into account the weight and its division.
EN - 10