Finding Information Please read and save this guide Thank you for choosing Electrolux, the new premium brand in home appliances. These Installation Instructions are part of our commitment to customer satisfaction and product quality throughout the life of your new appliance.
IMPORTANT The instructions in this manual and all other literature included with this washer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance.
The standpipe height above the floor should be: Minimum height: 24 in. (61 cm) Maximum height: 96 in. (244 cm) Drain hose attached to the washer can reach a 79 in. (201 cm) high standpipe. For higher standpipe, use hose P/N 137098000, available from an authorized parts distributor.
INSTALLATION IN A RECESS OR CLOSET If washer and dryer are installed in the same closet, door ventilation is required: A minimum of 120 square inches (774.2 cm²) of opening, equally divided at the top and bottom of the door, is required.
Installation Requirements Installed washer dimensions 50.6” (128.53cm)* to clear open door freestand washer on floor floor line washer mounted on optional pedestal floor line * To obtain these minimal depth dimensions, dryer must either be vented straight back or with a quick-turn 90° elbow.
Remove styrofoam base and shipping plug and set them aside. Carefully return the washer to an upright posi- tion. Carefully move the washer to within 4 feet (1 m) of its final location. IMPORTANT Save styrofoam base and shipping plug for use to help prevent washer damage during any future moves.
WRENCH (SUPPLIED) Save all shipping bolts and spacers for future 5 SPACERS use. If the washer is to be transported at a later date, the shipping hardware must be reinstalled 5 BOLTS to help prevent shipping damage. Locate 7 hole plugs in the small bag supplied with washer instruction guides.
Excessive noise and vibration can be prevented by properly leveling the washer. For free standing installation and with the washer within 4 feet (1 m) of its final location, place a level on top of the washer. Use the universal wrench to adjust the level- ing legs so the washer is level front-to-rear and side-to-side, and stable corner-to-corner.
Installation Instructions Connecting inlet water Run some water from the hot and cold faucets to flush the water lines and remove particles that might clog the water valve screens and to determine which faucet is hot and which is cold supply.
Place these instructions in a location near the washer for future reference. NOTE A wiring diagram and technical data sheet are located under the washer top panel, on top of the detergent dispenser housing. Installation Instructions CABLE TIE...
Use & Care Guide and enjoy your new premium washer! If your washer has this console: After you plug in the washer the first time: wake up the washer by pressing any button and then follow the prompts on the LCD User Interface, including language selection.
1 Be sure you have adequate swing area before reversing door. 2 You will need a screw driver with a #2 square bit. 3 Protect flat work surface, such as top of washer or floor near washer, with a soft cloth or towel.
Page 14
Reversing Door C) Removing Hinge from Front Panel 1 With the hinge in open position, remove 2 short, course-thread, panhead screws on hinge plate. 2 Remove 3 short, fine-thread, counter-sunk screws in hinge side. 3 Slide the hinge toward the center of the front panel, and then pivot the hinge inward while slowly pulling it away from the front panel to expose the attached harness.
Reversing door and hardware E) Reattaching Door Lock to Front Panel 1 Rotate the door lock and move it to the opposite opening. 2 Connect the harness to the door lock by inserting it in the terminal and firmly pushing it in place.
Page 16
Reversing Door G) Removing Striker Plate 1 Remove 2 long, course-thread, counter-sunk screws and striker plate. 2 Set the striker plate to the side for later. H) Removing Latch Indicator 1 Insert flat blade screwdriver into open slot of latch indicator. 2 Gently pry upward to release tab.
Page 17
J) Reinserting Latch Indicator 1 Rotate the latch indicator and move it to the opposite hole in the door. insert indicator through slot 2 Firmly insert the two small tabs on either side of the latch indicator into the two slots on either side of the hole in the door.
3 Insert the trim ring in the slots and rotate it clockwise approximately ¾”. P) Reinstalling Trim Plug 1 Open the door to a 90 degree angle. 2 Install the trim plug with 1 long, course- thread, panhead screw. Q) Plug in washer and continue operation.
Turquoise Sky Pedestal - P/N EPWD15TS A storage pedestal accessory, specifically designed for this washer may be used to elevate the dryer for ease of use. This pedestal will add about 15” (38.1cm) to the height of your unit for a total height of 53”...