Vimar ELVOX Quick Start Manual

4622.036B
Quick start guide
Camera
Telecamera Dome IP a colori Day & Night, sensore CMOS 1/2,8", risoluzione
2 Mpx (1920x1080), obiettivo fuoco fisso 3,6 mm, filtro IR meccanico, H.265 e
H.264 Multistream, funzioni AV, alimentazione PoE o 12 Vdc, IR 20-30 m, funzioni
WDR, 3DNR, HLC, BLC, Mask, Motion, Smart IR, RTSP, protocollo ONVIF, grado
di protezione IP67. Dimensioni: Ø 95x83 mm. Peso 430 g.
CD Drill template
Contenuto della confezione
Una volta ricevuto il dispositivo, controllare gli accessori indicati di seguito. Le illu-
strazioni sotto riportate hanno solo funzione di riferimento. Far riferimento all'appa-
recchiatura in dotazione.
3
Overview
Telecamera
Camera
Network Camera
Quick Start Guide
Introduzione
■ Please read this instruction carefully before operating the
Questa telecamera IP (abbreviato in IP-CAM) è stata progettata per fornire soluzioni 3
unit and keep it for further reference.
TVCC ad elevate prestazioni. Adotta chip di elaborazione video allo stato dell'arte.
■ All the examples and pictures used here are for reference only.
4
Utilizza le tecnologie più avanzate, di codifica e decodifica video ed è conforme al
■ The contents of this manual are subject to change without
5
notice.
protocollo TCP/IP, SoC.(System on chip) ecc. per assicurare la stabilità e l'affidabilità
del sistema. I manuali completi e i software CVM.exe, Iptool.exe e Diskcalculator.exe
is instruction carefully before operating the
sono disponibili nella scheda prodotto consultabile nel sito www.vimar.com
or further reference. 1
Warning and Caution
Connessioni
1
Ethernet connector
les and pictures used here are for reference only.
Di seguito sono riportate le principali connessioni della telecamera.
■ If the product does not work properly, please contact your dealer
Power connector
2
of this manual are subject to change without
or the nearest service center. Never attempt to disassemble the
3
Mounting base
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
4
Fixed screw
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the
product is mounted on wall or ceiling, the device shall be firmly
ng and Caution
fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
oes not work properly, please contact your dealer
■ Do not aim the camera at the sun or extra bright place.
vice center. Never attempt to disassemble the
■ Do not place the camera in extremely hot, cold (the operating
DC12V
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
(We shall not be responsible for any problems
not expose it to high electromagnetic radiation.
■ To avoid heat accumulation, good ventilation is required for
orized repair or maintenance.)
operating environment.
ater or liquid intrusion into the camera.
* 1 It is recommended to install the security cap for outdoor installation.
e product, you must be strict compliance with the
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
2
Package
egulations of the nation and region. When the
required.
Installazione
ed on wall or ceiling, the device shall be firmly
Prima di iniziare, assicurarsi che la parete o il soffitto siano sufficientemente solidi
0 ~360
per sopportare tre volte il peso della telecamera. La procedura di montaggio è la
seguente:
1) Allentare la vite di fissaggio per smontare la telecamera.
mera beyond specified voltage range.
2) Praticare i fori per le viti e per il cavo sulla parete utilizzando la dima di foratura.
e camera or subject it to physical shock. 3) Passare i cavi e collegare il cavo di alimentazione e il cavo di rete.
4) Fissare la base di montaggio della telecamera alla parete con le viti, come
g the camera lens.
descritto di seguito.
5) Prima della regolazione, visualizzare l'immagine della telecamera su un moni-
ecessary, please use clean cloth to wipe it gently.
0 ~360
° °
tor per regolare l'angolo di visuale della telecamera, quindi fissare la ghiera con
camera at the sun or extra bright place. la vite di fissaggio.
6) Per completare l'installazione rimuovere delicatamente la pellicola di protezione.
camera in extremely hot, cold (the operating
y, fix the camera with the fixed screw.
be -30˚C~60˚C), dusty or damp locations, and do
1
h electromagnetic radiation.
ccumulation, good ventilation is required for
Vite di
ment.
fissaggio/
Fixed
screw
ge
etwork Connection
ss Through IP-Tool
49401510A0 01 2106
Switch
Tapping screws × 3
×3
Screwdriver Plastic plug
Istruzioni per l'uso
Quick and start guide
Network Camera
1
Quick Start Guide
2
5
Microphone
Micro SD card slot
6
Reset
7
(a)
(a). Loosen the nut from the main element.
( ) b . Run the network cable (without RJ 45 connector) through the
both elements. Then crimp the cable with RJ 45 connector.
° °
( ) c . Connect the cable to the hermetic connector. Then tighten the
nut and the main cover.
0 ~75
° °
④ Secure the mounting base to the ceiling or wall with the screws provided.
2
44,2 mm
Fixed screw
38,2 mm
⑤ Install the dome and enclosure to the mounting base.
4
Installation
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
IP Dome Day&Night colour camera, CMOS 1/2.8" sensor, 2 Mpx (1920x1080) res-
the camera in the dry environment.
olution, 3.6 mm fixed focus lens, mechanic IR filter, H.265 and H.264 Multistream,
VA functions, PoE or 12 Vdc supply, IR 20-30 m, WDR, 3DNR, HLC, BLC, Mask,
① Loosen the fixed screw to disassemble the camera.
Motion, Smart IR, RTSP functions, ONVIF protocol, IP67 protection degree.
Dimensions: Ø 95x83 mm. Weight 430 g.
Package content
After you receive your device, please check the following accessories. The pictures
here are for reference only.
Dima di foratura
Screws & spiles
Drill template ② Unscrew the cover of the dome and then insert a micro SD card.
After that, install back the cover and make sure the cover is installed
firmly.
Quick start guide
Tapping screws × 3
Camera
Introduction
Quick start guide
Camera
6 CD Drill template
Screwdriver
This IP-camera (short for IP-CAM) is designed for high performance CCTV solu-
tions. It adopts state of the art video processing chips. It utilizes most advanced
Cover
technologies, such as video encoding and decoding technology, complies with the
7
TCP/IP protocol, SoC (System on chip), etc to ensure this system more stable and
reliable. Complete manuals and CVM.exe, Iptool.exe e Diskcalculator.exe software are
3
Overview
available to download in the Product info sheet section of www.vimar.com website.
CD Drill template
③ Drill the screw holes and the cable hole on the ceiling according
1
Connections
to the drill template. Then route and connect the cables.
Here below the main connections of the camera.
2
3
4
5
3
(a). Loosen the nut from the main element.
Overview
( ) b . Run the network cable (without RJ 45 connector) through the
1 5
Ethernet connector Microphone
both elements. Then crimp the cable with RJ 45 connector.
Power connector Micro SD card slot
2 6
44.2
( ) c . Connect the cable to the hermetic connector. Then tighten the
3 Mounting base Reset
7
4
Fixed screw
nut and the main cover.
38.2
④ Secure the mounting base to the ceiling or wall with the screws provided.
3
4
( ) c
(b)
DC12V
5
(a)
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
③ Modify the IP address. The default IP address of this camera is
required.
Installation
1
Ethernet connector
Before start, please make sure that the wall or ceiling is strong enough to withstand
(a). Loosen the nut from the main element.
192.168.226.201. Click the information of the camera listed in the
(a). Loosen the nut from the main element.
3 times the weight of the camera. The mounting steps are as follows:
Power connector
2
( ) b . Run the network cable (without RJ 45 connector) through the
above table to show the network information on the right hand.
( ) b . Run the network cable (without RJ 45 connector) through the
1) Loosen the fixed screw to disassemble the camera.
3 2) Drill the screw holes and the cable hole on the wall according to the drill template.
Mounting base
Modify the IP address and gateway of the camera and make sure its
both elements. Then crimp the cable with RJ 45 connector.
both elements. Then crimp the cable with RJ 45 connector.
3) Route the cables and connect the power cable and video cable.
network address is in the same local network segment as the
4
Fixed screw
4) Secure the mounting base with camera to the wall with screws as shown below.
( ) c . Connect the cable to the hermetic connector. Then tighten the
( ) c . Connect the cable to the hermetic connector. Then tighten the
5) Before the adjustment, display the image to a monitor and then adjust the camera
computer's. Please modify the IP address of your device according
nut and the main cover.
and then loosen the fixed ring to adjust the view angle of the camera angle. Final-
nut and the main cover.
to the practical situation.
ly, fix the camera with the fixed screw.
⑤ Install the dome and enclosure to the mounting base.
6) Remove the protective film to complete the installation procedure.
Modify Network Parameter
④ Secure the mounting base to the ceiling or wall with the screws provided.
④ Secure the mounting base to the ceiling or wall with the screws provided.
Mac Address
IP Address
4
Installazione della base
Subnet Mask
Base mounting
Ø91,6 mm
Gateway
DC12V
For example, the IP address of your computer is 192.168.1.4. So the Ø51,0 mm
* 1 It is recommended to install the security cap for outdoor installation. IP address of the camera shall be changed to 192.168.1.X. After
Ø4,5 mm
Then adjust the dome to obtain an optimum view angle.
modification, please enter the password of the administrator and click
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
"Modify" button to modify the setting.
required.
The default password of the administrator is "123456".
IT EN
⑤ Install the dome and enclosure to the mounting base.
⑤ Install the dome and enclosure to the mounting base.
④ Double-click the camera listed in the IP-Tool or manually enter
the IP address in the address bar of the web browser to connect IP
camera. Then follow directions to download and install the plugin.
⑤ Enter the username and password in the login interface.
Fixed Screw
Mounting Base
Enclosure
Dome
Viti Cacciavite Cappuccio impermeabile
Screw-driver
4
Installation
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install and use
the camera in the dry environment.
① Loosen the fixed screw to disassemble the camera.
Tapping screws × 3
×3
Plastic plug
Insert a micro SD card
② Unscrew the cover of the dome and then insert a micro SD card.
×3
Screwdriver Plastic plug
After that, install back the cover and make sure the cover is installed
firmly.
(a)
6
1 Cavo di rete / Network Cable
Cover
2 Cavo alimentazione / Power Cable
7
3 Base di fissaggio / Mounting base
4 Vite di fissaggio / Fixing screw
③ Drill the screw holes and the cable hole on the ceiling according
5 Microfono / Microphone
to the drill template. Then route and connect the cables.
6 Slot micro SD card / Micro SD card slot
7 Reset
(mm) 1
Ø91.6
2
44.2
Ø51.0
Ø4.5
38.2
7
(a)
(b)
(b)
⑥ Finally, fix the camera with the fixed screw.
5
Microphone
Micro SD card slot
6
Reset
7
CE :98 :23 :75 :35 :22
5
Network Connection
192 .168 . 1 . 201
5
Montaggio alla base
255 . 255 . 255 . 0
Mounting to the base
192 .168 . 1 . 1
● Access Through IP-Tool
Modify
IPC
① Make sure that the camera and the PC are connected to
network.
② Install IP-Tool from the CD and run it after installation
Immediate Refresh
Water-proof Cap
4
Installat
Please make sure that t
Fixed Screw
withstand 3 times the w
Mounting Base
Enclosure
the camera in the dry en
Dome
① Loosen the fixed scr
( ) c
(b)
Insert a micro SD card
② Unscrew the cover o
After that, install back
firmly.
0 ~360
° °
(mm)
Ø91.6
6
Cover
0 ~75
° °
Ø51.0
Ø4.5
0 ~360
° °
( ) c
( ) c
③ Drill the screw hole
Earth wire connection
Earth wire connection
to the drill template. T
⑥ Finally, fix the cam
⑥ Finally, fix the came
Fixed screw
44.2
5
38.2
5 Network
Network
Switch
● Access Throug
● Access Through
Network Cable Network Cable
Router
IPC
IPC
Viale Vicenza, 14
① Make sure that th
36063 Marostica VI - Italy ① Make sure that the
www.vimar.com
network.
network.
Device Network Search
② Install IP-Tool fro
② Install IP-Tool from
⑥
5
●
①
ne
②
Imm
Dev
na
na
na
Co
Net
Netwo
To