Warmup 6iE mini User Manual
Wifi thermostat
Hide thumbs
Also See for 6iE mini:
- User manual (18 pages) ,
- Quick start manual (2 pages) ,
- User manual (19 pages)
Related Manuals for Warmup 6iE mini
Summary of Contents for Warmup 6iE mini
- Page 1 mini WiFi Thermostat The smartest, most efficient way to control the world’s best selling floor heating. Miniaturised. User Guide...
-
Page 2: Table Of Contents
Step 3 - Thermostat Mounting ................ 6 Table 1.0 Thermostat Application ..............7 Step 4 - Initial Setup ..................7 Welcome to the 6iE mini .................. 8 How to quickly change the temperature ..............8 How to quickly change mode ................... 8 Heating ....................... -
Page 3: Safety Information
Zones 0, 1 and 2. If this is not possible then it must be installed in an adjacent room, controlling the rooms using the floor sensor only. The 6iE mini and its packaging are not toys; do not allow children to play with them. Small components and packaging present a risk of choking or suffocation. -
Page 4: Step 2 - Wiring Connections
Step 2 - Wiring Connections WARNING! The 6iE mini must be installed by a qualified electrician in accordance with the current edition of the BS7671 Wiring Regulations. NOTE: For loads above 10 A, the conductor wire gauge should be at least 2.5mm²... -
Page 5: Wiring Connections - Loads Over 16 Amps
Step 2 - Wiring Connections - Loads over 16 amps Warmup thermostats are rated for a maximum of 16 amps (3680 W). A contactor must be used to switch loads exceeding 16 amps. Please see wiring diagram below. ≤16A ≤16A... - Page 6 Table 1.0 Thermostat Use Cases Use Case System Type Control Limit Sensor Thermostat IN room Internal Air temperature schedule None Air Sensor No floor limit Thermostat IN/OUT of room Probe 1 (5 & 6) Floor temperature schedule None Floor limit Floor Sensor Thermostat IN room Probe 1...
-
Page 7: Step 3 - Thermostat Mounting
Step 3 - Thermostat Mounting 1,500W Insert fixing screws through Re-attach the front housing until a mounting holes of the power base “click” is heard. You can now power and tighten. up the 6iE mini. Thermostat WiFi Setup System Input Input application... -
Page 8: Step 4 - Initial Setup
Step 4 - Initial Setup ‘MyHeating’ by Warmup Download the MyHeating App. Open the My Heating App and scan the QR Code on the 6iE mini screen protector or on reverse of the display. Follow the instructions in the App to complete setup. -
Page 9: Welcome To The 6Ie Mini
Welcome to the 6iE mini Next/Accept Back/Cancel Up/Down Change value/setting How to quickly change the temperature Press to change your target temperature. If in program mode this will set a temporary override until your next heating period. See “How to set a temporary override”. -
Page 10: Heating
Heating How to set a program Setting a program allows you to set comfort temperatures at set times throughout the day. Days can programmed individually, all days the same or weekdays as a block and weekends as a block, the choice is yours. Edit Program To select the days you wish to program press... -
Page 11: How To Set Into Manual Mode
Heating How to set into Manual Mode Setting into manual mode allows you to set a fixed target temperature for the thermostat to achieve. The thermostat will continue to maintain this temperature until another operating mode or temperature is selected. 23.0 °... -
Page 12: Energy Monitor
Energy Monitor How Energy Monitor works The 6iE mini learns how you use your system and how your house reacts to heating and weather. Using the MyHeating App, energy monitoring will show the amount of energy consumed over a certain time period. This will be calculated through system power multiplied by efficiency and run time. -
Page 13: Settings
Settings Date and time Set the current date and time. 6-5-2021 Press to begin, press to change date/ 13:00 time. Press to confirm. Thermostat application Swaps probe usage, 1 being the Control Sensor Probe and 2 being the Limit Sensor Probe. Press to swap probe usage. - Page 14 Switch display lock off. WiFi WiFi Setup Open MyHeating App and scan the QR code on the back of the 6iE mini display to complete WiFi setup. Factory reset Factory reset will erase all of your settings and restore the thermostat to factory defaults.
-
Page 15: Notifications & Error Codes
App) Troubleshooting Display is blank Power (Electrician Required) Electrician required to verify power is going to the 6iE mini and that it is correctly wired. Control 1. Please see Table 1.0 and ensure you have (5 & 6) / selected the correct thermostat application. -
Page 16: Wifi Troubleshooting
10-15 seconds now work as reattach. Does the thermostat normal connect to your WiFi Network? Contact Warmup If the thermostat connected Set up a mobile hotspot using with your router to a mobile hotspot a smartphone. On a separate make &... -
Page 17: Technical Specifications
Warranty 12 Years Approvals BEAB NOTE: Hereby, Warmup plc, declares that the radio equipment type RSW-02-XX-YY is in compliance with the RED Directive 2014/53/EU and Radio Equipment Regulations 2017. The declarations of conformity may be consulted by scanning the QR Code or visiting www.literature.warmup.co.uk/d-o-c/6iE-mini. -
Page 18: Warranty
Warmup heater. If at any time during the warranty period the product is determined to be defective, Warmup shall repair or replace it, at Warmup’s option. If the product is defective, please either; Return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it, or Contact Warmup. - Page 19 Warmup plc www.warmup.co.uk uk@warmup.com T: 0345 345 2288 F: 0345 345 2299 Warmup plc 704 Tudor Estate Abbey Road London NW10 7UW Warmup GmbH Ottostraße 3 27793 Wildeshausen Warmup - UG - 6iE mini - V1.1 2022-01-07_EN...