Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for VESTEL BLDC Pyrojet Series
Summary of Contents for VESTEL BLDC Pyrojet Series
- Page 1 Service Manual BLDC Pyrojet Series...
-
Page 2: Table Of Contents
9.6. Electronic Pressure Sensor (EPS)* ............................31 9.7. Motor ....................................32 9.8. Door Lock* .................................... 33 9.9. Pyrojet* ....................................34 10. Wiring Diagram* ............................... 35 Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 2... - Page 3 You can also open a support ticket using Service Support Page: https://www.vestelservice.com/VestelService/ Acronyms: Washing Machine WMCS : Washing Machine Customer Support Twinjet User Interface Service Interface Available Not Available Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 3...
-
Page 4: Safety Precautions
Always use original spare parts. You may harm appliance, end user, environment or yourself using untested and unapproved 3rd party spare parts. Use right tools to prevent any wear or damage to components during assembly/disassembly. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 4... -
Page 5: Specifications
This avoids spinning while load is unbalanced and prevents any possible physical harm both to the appliance and to surroundings. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 5... -
Page 6: Assambly Information
= Water enters from Valve 1 Softener Main Wash = Water enters from Valve 2 Prewash Softener = Water enters from Valve 1 and 2 Valve 2 Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 6... -
Page 7: Control Panel And Acronyms
Door Closed and Delay Start Sound Next Selection Unlocked Temperature Sound On Door Open Select Cold Wash Sound Off Dosage Indıcator Cancel Spin Speed Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 7... -
Page 8: Test Mode
If the SW4 button is pressed as long as 10 seconds during The service mode, counter will appear. Counter shows the program detail which program knob Set on at the moment. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 8... - Page 9 EV1 + EV2 valves up to first level frequency (Depends on the water level) NTC check Heather resistance Pump Twinjet activation EPS measurement End Visualization (On Display) Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 9...
-
Page 10: Service Mode
SW3 which normally are not displayed to end user. If case of no error service autotest ends and "End" is displayed. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 10... -
Page 11: Failure Codes
The bolts/nuts above are important for product safety purposes. Please tighten screw, bolts and nuts according to the torque values given in table above. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 11... -
Page 12: Disassembly And Assembly Instructions
Put the door outside plastic with helping Remove screws that fix the door group. screwdriver. Remove the door inside plastic. Remove six screws that fix the door hinge. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 12... -
Page 13: Spring Wire
8.5. Control Panel Remove the screw which fixes the control Remove two screws fixing control panel. panel to the front panel. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 13... -
Page 14: Electronic Card & Fuse
8.6. Electronic Card & Fuse Remove PCB box using a small screw driver Remove the clip fixing the cover. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 14... -
Page 15: Front Panel
Remove the tub bellows seal. remove the door lock by pressing. Remove two screws fixing front panel to Remove the screw fixing twinjet elbow body Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 15... -
Page 16: Support Bracket
Unplug connectors from feed valve holder extensions of bellow hose Slightly turn the feed valve counter- Remove the detergent drawer housing clockwise to remove assembly Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 16... -
Page 17: Power Cable Group And Emi Filter
Pull the power cable group up Remove EMI filter 8.11. Electronic Pressure Switch (EPS) Unplug EPS connector Pull EPS up Remove clamp from EPS hose Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 17... -
Page 18: Door Lock
8.15. Front Counterweight* Remove three screws on the front Gently pull counterweight out counterweight. (Wrench size 13 mm) Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 18... -
Page 19: Heater
Remove the screws that fix the pyrojet unit available if not bend it to the other side. Remove the pyrojet unit by pulling upwards. Remove the conncetions. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 19... -
Page 20: Twinjet System
Remove screw fixing circulation pump machine by removing the screws Lay the appliance down and press on ratchet Remove circulation pump holding circulation pump Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 20... -
Page 21: Tub Bellow Seal
Hold the transport screw and pull it out. 8.21. Upper Counterweight* Remove two screws fixing the upper counterweight by using box wrench size 13 Hold and carry upper-counterweight out. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 21... -
Page 22: Washing Group
8.25. Driven Pulley Remove the bolt at the center of pulley by Remove pulley tucking a wooden bar avoids rotation Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 22... -
Page 23: Motor
Remove tub outlet bellowed hose loosening Remove 19 screws around tub using box screwed-clamp wrench size 8 mm Remove front tub Remove drum Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 23... -
Page 24: Bldc Card
Remove the card box that belongs to the Remove the card by pressing the clips pyrojet unit, by pressing the clips with screw around with screw driver. driver. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 24... - Page 25 Remove the card completely Remove the ground connection and make Remove the BLDC motor card fixing screws. sure this connection is plugged during the assembly. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 25...
-
Page 26: Component Specifications
(refer wiring diagram in section 12) as shown below figure. Resistance value should be between 131- 141 Ω Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 26... -
Page 27: Circulation Pump
(refer wiring diagram in section 12) as shown below figure. Resistance value should be between 160- 180 Ω Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 27... -
Page 28: Heater
Please contact WMCS for nominal measurement values of resistance used in your appliance. Do not forget to provide serial number information of appliance in your inquiry. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 28... -
Page 29: Ntc
(refer wiring diagram in section 12) as shown in below figure. NTC resistance value varies depending on temperature. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 29... -
Page 30: Valve
14th and white cable at 15th position in the large socket (refer wiring diagram in section 12) as shown in below figure. Each valve coil resistance values should be between 3.3 - 4.2 kohm. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 30... -
Page 31: Electronic Pressure Sensor (Eps)
Check water level from door glass. The water level should be just below door glass as seen in the picture below: (There is a %10 tolerance with this level) Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 31... -
Page 32: Motor
Ferrite Magnet Stator resistance (phase- Neutral) 2,38 ± 7% Ω Motor socket terminals Measurement of resistance and inductance are done between the terminals. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 32... -
Page 33: Door Lock
This socket shows the connection between terminal 3-4 (See wiring diagram below). The resistance read from terminal 3-4 is the resistance of PTC overload plus resistance of solenoid. Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 33... -
Page 34: Pyrojet
Self reset temperature 95 ± 5 °C Testing component Resistance value on the should be 52,6Ω ±20% at 25 °C. Self Resetting Termostat Termal Fuse Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 34... -
Page 35: Wiring Diagram
10. Wiring Diagram* Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 35... - Page 36 Prapared by Customer Technical Supoort Department in Vestel Washing Machine Plant – Manisa – Turkey Page 36...
Need help?
Do you have a question about the BLDC Pyrojet Series and is the answer not in the manual?
Questions and answers