Download Print this page
RKI Instruments 65-2330RK Operator's Manual

RKI Instruments 65-2330RK Operator's Manual

Hydrogen sulfide transmitter
Hide thumbs Also See for 65-2330RK:

Advertisement

Quick Links

Part Number: 71-0197RK
Revision: A
Released: 6/11/20
1.800.561.8187
information@itm.com
www.
.com

Advertisement

loading
Need help?

Need help?

Do you have a question about the 65-2330RK and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for RKI Instruments 65-2330RK

  • Page 1 Part Number: 71-0197RK Revision: A Released: 6/11/20 1.800.561.8187 information@itm.com www. .com...
  • Page 2 WARNING 1.800.561.8187 information@itm.com www. .com...
  • Page 3 OBLIGATIONS OR LIABILITIES ON THE PART OF RKI INSTRUMENTS, INC. INCLUDING BUT NOT LIMITED TO, THE WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL RKI INSTRUMENTS, INC. BE LIABLE FOR INDIRECT, INCIDENTAL, OR CONSEQUENTIAL LOSS OR DAMAGE OF ANY KIND CONNECTED WITH THE USE OF ITS PRODUCTS OR FAILURE OF ITS PRODUCTS TO FUNCTION OR OPERATE PROPERLY.
  • Page 4 1.800.561.8187 information@itm.com www. .com...
  • Page 5 WARNING: Do not use this product in a manner not specified in this instruction manual. WARNING: When using the 65-2330RK, you must follow the instructions and warnings in this manual to assure proper and safe operation of the 65-2330RK and to minimize the risk of personal injury.
  • Page 6 Controller Terminal Strip Factory Adjust Pot Span Pot Zero Pot Amplifier Detector Terminal Strip + Test Point (Red) 100 mV - 500 mV Range - Test Point (Black) J-Box H2S Detector 1.800.561.8187 information@itm.com www. .com...
  • Page 7 Detector Housing Body Cap Gasket Plug-In H2S Sensor Detector Housing Cap Hydrophobic Membrane Detector Housing Body Housing Cap & Cap Gasket Plug-In H S Sensor 1.800.561.8187 information@itm.com www. .com...
  • Page 8 Controller Terminal Strip Detector Terminal Strip Zero Pot Span Pot CAUTION:The third potentiometer is factory-set. Do not adjust it. Test Points 1.800.561.8187 information@itm.com www. .com...
  • Page 9 3.10 3/4 NPT Female 3.65 6.8 Max Rubber Spacers J-Box H2S Detector 1 1 /2-20 T hread for Calibration Cup 1.800.561.8187 information@itm.com www. .com...
  • Page 10 WARNING: Always verify that power to the controller is OFF before you make wiring connections. CAUTION:If shielded cable is used, leave the cable shield’s drain wire insulated and disconnected at the transmitter. You will connect the opposite end of the cable’s drain wire to the controller’s chassis (earth) ground.
  • Page 11 4 - 20 mA In (S) + 24 VDC Cable Shield Controller J-Box Black H2S Detector 1.800.561.8187 information@itm.com www. .com...
  • Page 12 CAUTION:Allow the transmitter to warm up for 5 minutes before you continue with the next section, “Setting the Zero Signal”. 1.800.561.8187 information@itm.com www. .com...
  • Page 13 Daily Quarterly 1.800.561.8187 information@itm.com www. .com...
  • Page 14 Note: Under “normal” circumstances, the transmitter requires calibration once every 3 months. Some applications may require a more frequent calibration schedule. Replacing the Plug-In H S Sensor CAUTION:The sensor contains electrolyte which is a dilute acid. Do not disassemble the sensor when replacing it with a new one.
  • Page 15 WARNING: The H S sensor will not operate properly if the wire jumper is not removed. Remove jumper CAUTION:Allow the replacement sensor to warm up for 5 minutes before you continue with the next step. Replacing the H S Detector 1.800.561.8187 information@itm.com www.
  • Page 16 CAUTION: Allow the replacement detector to warm up for 5 minutes before you continue with the next step. Replacing the Hydrophobic Membrane Replacing the Amplifier 1.800.561.8187 information@itm.com www. .com...
  • Page 17 1.800.561.8187 information@itm.com www. .com...
  • Page 18 WARNING: Do not remove the detector housing cap or junction box cover while the circuits are energized unless the area is determined to be non-hazardous. Keep the detector housing cap and junction box cover tightly closed during operation. Output (mV) = (calibrating sample/fullscale) X 400 + 100 200 (mV) = (25/100) X 400 +100 1.800.561.8187 information@itm.com...
  • Page 19 1.800.561.8187 information@itm.com www. .com...
  • Page 20 1.800.561.8187 information@itm.com www. .com...