Power/Data Cable Wiring - Garmin GPSMAP 3006C Installation Instructions Manual

Power/Data Cable Wiring

The following pages contain several wiring diagrams. The first diagram on the next page shows the GPSMAP 3006C/3010C MFD using the
18-pin Power/Data wiring harness and the GPS 17. If two or more GPSMAP 3006C/3010C units are installed and networked, only one GPS 17
antenna needs to be installed. Next are the wiring diagram examples showing the GPSMAP 3006C/3010C using the 18-pin Power/Data wiring
harness interfacing with a variety of different equipment. Refer to the wiring diagram that best suits your needs. For third-party devices, refer
to the wiring guidelines included with that equipment. Use 22 AWG (18 AWG for the Red and Black wires), shielded, twisted-pair wiring for
extended runs of wire. Solder all connections and seal the connection with heat shrink tubing. If networking two or more MFDs, the GPS 17
and NMEA input devices should only be attached to one MFD on the network. A pinout of the cable is shown below.
Power/Data Cable Input/Output Ports
The GPSMAP 3006C/3010C Power/Data cable has four I/O (Input/Output) ports.
Ports 1 and 2—communicate with other NMEA-compliant devices, such as VHF radios, NMEA instruments, autopilots, or PCs (Port 1 only).
You can input one NMEA device to each port, and output in parallel to three NMEA devices per port.
Port 3—is reserved for use with Garmin sounder modules.
Port 4—is reserved for use with the Garmin GPS 17 GPS/WAAS antenna.
The following formats are supported for connection of external devices: Garmin proprietary sonar module and NMEA 0183 version 3.01. The
following are the sentences for NMEA 0183, version 3.01 and later output:
Approved sentences—GPBWC, GPRMC, GPGGA, GPGSA, GPGSV, GPGLL, GPBOD, GPRMB, GPRTE, GPVTG, GPWPL, and GPXTE.
Garmin proprietary sentences—PGRME, PGRMM, PGRMZ, and PSLIB.
The unit also includes NMEA input with support for the WPL sentence, DSC, and sonar NMEA input with support for the DPT (Depth) or
DBT, MTW (Water Temp), and VHW (Water, Speed, and Heading) sentences. The unit interface must be set to NMEA In/NMEA Out.
Documentation concerning NMEA & RTCM formats and
sentences are available for purchase from:
National Marine Electronics Association (NMEA)
Seven Riggs Avenue
Severna Park, MD 21146
U.S.A.
www.nmea.org
GPSMAP 3006C/3010C & GPS 17
Power/Data(NMEA) Cable
PIN # COLOR
1 N/C
2 N/C
3 N/C
4 WHITE/BROWN
5 WHITE/BLUE
6 ORANGE
7 N/C
8 N/C
9 VIOLET
10 GRAY
11 YELLOW
12 N/C
13 WHITE
14 GREEN
15 RED
16 BROWN
17 BLUE
18 BLACK
I
NSTALLATION
1
2
6 5 4 3
7
11 10 9 8
15 14 13 12
18
17 16
Cable End View
FUNCTION
PORT 3 DATA IN
PORT 3 DATA OUT
ACCESSORY ON
PORT 2 DATA IN
PORT 2 DATA OUT
ALARM LOW
PORT 4 DATA IN
PORT 4 DATA OUT
DC POWER INPUT
PORT 1 DATA IN
PORT 1 DATA OUT
GROUND (POWER/DATA)
I
NSTRUCTIONS
7