Advertisement
Connect Family
The RE667 Slimline Touchpad
for controlling the security system. It is AC powered and
communicates with the panel wirelessly.
Features
• Vibrant 7'' Android™ tablet display
• Provides local control of security and automation functionality
• Wall or table mounted
• Encrypted, Connect+ and BAT-Connect enabled, battery-backed
Wi-Fi™ connection
Installation Overview for Connect+
1. Confirm the panel has a Wi-Fi DeviceLink card installed.
Installing the Wi-Fi DeviceLink Card
• Disconnect the panel's AC power and backup
battery.
• Install the Wi-Fi DeviceLink card in Slot 2 by
carefully aligning the nylon retention posts and
the 8-pin connector while pushing the card
firmly until all posts are fully seated.
• Reconnect the panel's AC power and backup
battery.
• Verify the Wi-Fi card LEDs are on.
2. Choose a mounting location. Touchpad can be mounted on a wall or tabletop.
3. Identify your network and verify signal strength before mounting it permanently.
1. Ensure the panel is powered.
2. Power the Touchpad by applying AC power.
3. Select the "Connect" option to see the available networks. If the "Connect" option is
not available, press "Setup" then "Factory Default". The Touchpad can be connected
to either the Wi-Fi DeviceLink card or the home router for internet access. (Internet
access allows for camera control, weather updates, and the ability to modify users.)
4. Once a network is determined, verify the signal strength. If the signal strength
displayed is less than 35, relocate the Touchpad or Connect+ panel. If neither options
are available, install an RE621 Touchpad Range Extender.
Note: If connecting to a home network router, the Connect+ needs to be connected
to the same network via ethernet. The Touchpad cannot connect to the panel over an
unsecured or open network.
RE667 SlimlineTouchpad
is an intuitive interface
Slot
AC
Power
Input
Backup
Battery
I
2
Advertisement
Table of Contents
Related Manuals for Alula Slimline RE667
Summary of Contents for Alula Slimline RE667
- Page 1 RE667 SlimlineTouchpad Connect Family The RE667 Slimline Touchpad is an intuitive interface for controlling the security system. It is AC powered and communicates with the panel wirelessly. Features • Vibrant 7’’ Android™ tablet display • Provides local control of security and automation functionality •...
- Page 2 • Tap the "Restart" button to tryagain. 6. If using cameras or user management features, you must log in to the Alula Cloud as the account owner. To log in go to Settings and select Touchpad. Enter master code, then select Alula Cloud.
- Page 3 Installation Overview for BAT-Connect 1. Chose a mounting location. Touchpad can be mounted on a wall or tabletop. 2. Identify your network and verify signal strength before mounting it permanently. 1. Ensure the system is powered. 2. Power the Touchpad by applying AC power. Note: The Touchpad cannot run off panel bus.
- Page 4 BAT-Connect must be connected via ethernet or Wi-Fi. In addition you must log in to the Alula platform using the account owner username and password. To log in go to Settings and select Touchpad. Enter master code, then select Alula Cloud.
-
Page 5: Wall Mounting
Wall Mounting 1. There are two mounting configurations. A. If mounting on a stud, use the two centered holes labeled below [A]. B. If not mounting on a stud, use the four corner mounting holes. Insert the wall anchors prior to screwing the screws in place [B]. -
Page 6: Menu Guide
5. Lock in cover by pressing 3. Slide the Touchpad 4. Drop cover behind at these locations until onto the mounting plate. Touchpad. snapped into place. Push any extra wire into wall before sliding onto mounting plate. 6. Plug in powersupply. Menu Guide Dashboard •... - Page 7 Devices (continued) • Open and close Z-Wave garage door openers • Control Z-Wave thermostats **PLEASE SEE Z-WAVE USER GUIDE FOR ADDITIONAL INFORMATION** Cameras • Cameras can be viewed directly from the Touchpad. Live view, clips, and event notifications are supported. Doorbell live view will automatically be displayed when the doorbell button is pressed.
- Page 8 • Wi-Fi - connect via Wi-Fi if using cameras and user management features • Temperature Scale - option for displaying °F or °C • Alula Cloud - must be logged into Alula Cloud as the account owner to use cameras and user management features...
- Page 9 • Panel (must enter code to access) • Global Chime - enables or disables panel sensor chime mode • Quick Arm - arm the panel without entering your access code. Access code is still required to disarm. • Manage Access - manage device users directly from the touchpad (only the account owner can modify users, internet access isrequired) •...
-
Page 10: Home Screen Functions
Home Screen Functions* The time zone can be config- ured on Alula Connect Tap to turn the Touchpad’s The headline indicates panel status such as display off “Disarmed” or “Armed Stay” Tap to mute beeps during arm/disarm Tap to edit favorite zones,... - Page 11 Connect+, and the DeviceLink connection are battery backed. If the Touchpad is connect- ed only via the premise Wi-Fi, Alula recommends that all network equipment including the Wi-Fi access point be connected to a suitable UPS to ensure system availability during power outage.
-
Page 12: Specifications
TRADEMARKS Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this Alula and Connect+ are trademarks owned by Alula Holdings, LLC. Android is a trademark of Google LLC. equipment. Z-Wave is a registered trademark of Silicon Labs. Wi-Fi is a This device complies with part 15 of the FCC Rules. - Page 13 RF exposure requirements, and should be avoided. 0mm from the body. To maintain compliance with FCC RF exposure requirements, 47-00018 • Rev A • 2021-11-29 Tech Support Line • (888) 88-ALULA • (888) 882-5852 alula.com...
Need help?
Do you have a question about the Slimline RE667 and is the answer not in the manual?
Questions and answers