Alula RE667 Manual
  1. Manuals
  2. Brands
  3. Alula Manuals
  4. Touch Panel
  5. RE667
  6. Manual

Alula RE667 Manual

Slimline touchpad connect+ encrypted
Hide thumbs Also See for RE667:

Advertisement

Table of Contents

Connect Family
The RE667 Slimline Touchpad
controlling the Connect+ security system. It is AC powered and
communicates with the panel wirelessly.
Features
• Vibrant 7'' Android tablet display
• Provides local control of security and automation functionality
• Wall or table mounted
• Encrypted, Connect+ enabled, battery-backed Wi-Fi™ connection
Installation Overview
1. Confirm the panel has a Wi-Fi DeviceLink card installed if using with Connect+.
Installing the Wi-Fi DeviceLink Card
• Disconnect the panel's AC power and backup
battery.
• Install the Wi-Fi DeviceLink card in Slot 2 by
carefully aligning the nylon retention posts and
the 8-pin connector while pushing the card
firmly until all posts are fully seated.
• Reconnect the panel's AC power and backup
battery.
• Verify the Wi-Fi card LEDs are on.
2. Choose a mounting location. Touchpad can be mounted on a wall or tabletop.
3. Verify signal strength at the desired location before mounting it permanently.
Verifying Signal Strength
1. Make sure the panel is powered and the Wi-Fi DeviceLink card is installed.
2. Power the Touchpad by applying AC power.
3. Select the "Connect" option to see the available networks. If the "Connect" option is
not available, press "Setup" then "Factory Default".
4. If the signal strength displayed is less than 35, relocate Touchpad or Connect+ panel. If
neither options are available, install an RE621 Touchpad Range Extender.
RE667 Slimline Touchpad
Connect+
is an intuitive interface for
Encrypted
™
AC Power
Input
I
Slot 2
Backup
Battery

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RE667 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Alula RE667

Summary of Contents for Alula RE667

  • Page 1 RE667 Slimline Touchpad Connect+ Encrypted ™ Connect Family The RE667 Slimline Touchpad is an intuitive interface for controlling the Connect+ security system. It is AC powered and communicates with the panel wirelessly. Features • Vibrant 7’’ Android tablet display • Provides local control of security and automation functionality •...
  • Page 2 4. Mount the Touchpad. Refer to section “Touchpad Mounting Options” for mounting instructions. 5. Enroll the Touchpad by pressing the enroll button on the side of the panel until it beeps once and then selecting the desired panel on the Touchpad. Note, the Touchpad will list all panels within range, not just the ones in enrollment mode.

  • Page 3: Wall Mounting

    2. Slide the Touchpad onto the stand. The fit is intended to be quite snug, so some force may be required for the stand to “click” into place. 3. Coil up the excess power wire into the stand, and close the stand cover to contain the wires. 4.
  • Page 4 2. There are two methods for connecting power to the Touchpad. A. If you desire to hide the power cable, you can drill a hole in the wall through one of the four windows in the mounting plate and pull a wire behind the drywall to a location with an AC power outlet.

  • Page 5: Menu Guide

    Menu Guide Security • History - shows event history • Attention - shows all opened, bypassed, or troubled zone. Zones can be bypassed or activated by pressing the toggle to the right of the zone name. Scenes • Create scenes from the Touchpad by clicking the “+ Add” button •...
  • Page 6 Settings • Display • Brightness - adjust slide bar to change brightness level • Auto sleep display - when enabled the Touchpad screen will go to sleep after programmed period of inactivity. When disabled the Touchpad screen will stay on and show the system overview page.
  • Page 7 • Panel (Continued) • Check for updates - this will tell the panel to check for any system updates • Z-Wave • Join/Leave Another Z-Wave Network - the panel can be placed into Z-Wave inclusion or exclusion mode to allow it to join/ leave existing Z-Wave networks. •...

  • Page 8: Home Screen Functions

    Home Screen Functions The headline indicates panel status such as "Disarmed" or "Armed Stay" Tap or slide to view Side Menu Tap to mute beeps during arm/disarm action Tap to view Panic options and then press desired Panic option for two seconds to trigger The time zone is Tap to turn the configured online...

  • Page 9: Panic Functions

    Panic Functions Hold for two seconds to trigger Hold for two seconds auxiliary alarm to trigger fire alarm Hold for two seconds to trigger police alarm Turn on/off individual panics...
  • Page 10 Pro Tips Push any extra wire into wall before sliding Touchpad onto mounting plate to ensure the wires don’t get pinched. Drill a hole in the wall through any of the 4 mounting plate windows if no hole exists. The Touchpad display turns off on its own after specified allotted time of inactivity (Auto sleep display setting).
  • Page 11 THIS PAGE IS INTENTIONALLY LEFT BLANK...

  • Page 12: Specifications

    Changes or modifications not expressly approved by Alula could Le présent appareil est conforme aux cnr d’Industrie void the user’s authority to operate this equipment. Canada applicables aux appareils radio exempts de licence.

Table of Contents

Save PDF