Table of Contents
Advertisement
Quick Links
Connect Family
he RE657WF Flat Mount Touchpad i
T
the Connect+ security system. Designed to cover unsightly marks, the Flat
Mount Touchpad is well suited for takeover situations. It is AC powered and
communicates with the panel wirelessly.
Features
• Vibrant 7" Android™ tablet display
• Provides local control of security and automation
functionality
• Expanded footprint for covering marks left by
pre-existing keypads
• Encrypted, Connect+ enabled, battery-backed
Wi-Fi™ connection
Installation Overview
1. Confirm the panel has a Wi-Fi DeviceLink card installed.
Installing the Wi-Fi DeviceLink Card
• Disconnect the panel's AC power and backup
battery.
• Install the Wi-Fi DeviceLink card in Slot 2 by
carefully aligning the nylon retention posts and
the 8-pin connector while pushing the card
firmly until all posts are fully seated.
• Reconnect the panel's AC power and backup
battery.
• Verify the Wi-Fi card LEDs are on.
2. Verify signal strength at the desired location before mounting it permanently.
Verifying Signal Strength
1. Make sure the panel is powered and the Wi-Fi DeviceLink card is installed.
2. Power up the Touchpad.
3. Select the "Connect" option to see the available networks. If the "Connect" option is
not available, press "Setup" then "Factory Default".
4. If the signal strength displayed is less than 35, relocate Touchpad or Connect+ panel. If
neither options are available, install an RE621 Touchpad Range Extender.
RE657WF Flat Mount Touchpad
Connect+
Encrypted
™
s an intuitive interface for controlling
AC Power
Input
I
Slot 2
Backup
Battery
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alula RE657WF
Summary of Contents for Alula RE657WF
- Page 1 Encrypted ™ Connect Family he RE657WF Flat Mount Touchpad i s an intuitive interface for controlling the Connect+ security system. Designed to cover unsightly marks, the Flat Mount Touchpad is well suited for takeover situations. It is AC powered and communicates with the panel wirelessly.
- Page 2 3. Finish mounting the Touchpad. See Touchpad Mounting for detailed instructions. 4. Enroll the Touchpad by pressing the enroll button on the side of the panel until it beeps once and pressing “Connect” on the Touchpad. Then select the desired panel on the Touchpad. Note, the Touchpad will list all panels within range, not just the ones in enrollment mode.
- Page 3 Touchpad Mounting 1. Open the enclosure by lifting at the single point with a flathead screw driver at the location shown below. 2. Remove the display by pulling it out of the back plastic. Display 3. Mount the enclosure to the wall using the screw holes in the enclosure. Insert the wall anchors prior to securing the screws in place.
-
Page 4: Power Transformer
Power Converter Splice Power Transformer Display See table below for Max Wire Length 4. Pull wire from touchpad to AC outlet. If replacing an existing touchpad, existing wiring can be used; however, new touchpad must be powered by supplied 12V DC power transformer. Do not power from existing panel. -
Page 5: Menu Guide
Menu Guide Security • History - shows event history • Attention - shows all opened, bypassed, or troubled zone. Zones can be bypassed or activated by pressing the toggle to the right of the zone name. Scenes • Create scenes from the Touchpad by clicking the “+ Add” button •... - Page 6 Menu Guide (Continued) Settings • Display • Brightness - adjust slide bar to change brightness level • Auto sleep display - when enabled the Touchpad screen will go to sleep after programmed period of inactivity. When disabled the Touchpad screen will stay on and show the system overview page.
- Page 7 Menu Guide (Continued) Settings (Continued) • Panel (Continued) • Check for updates - this will tell the panel to check for any system updates • Z-Wave • Join/Leave Another Z-Wave Network - the panel can be placed into Z-Wave inclusion or exclusion mode to allow it to join/ leave existing Z-Wave networks. •...
-
Page 8: Home Screen Functions
Home Screen Functions The headline indicates panel status such as "Disarmed" or "Armed Stay" Tap or slide to view Side Menu Tap to mute beeps during arm/disarm action Tap to view Panic options and then press desired Panic option for two seconds to trigger The time zone is Tap to turn the configured online... -
Page 9: Panic Functions
Panic Functions Hold for two seconds to trigger Hold for two seconds auxiliary alarm to trigger fire alarm Hold for two seconds to trigger police alarm Turn on/off individual panics... - Page 10 Pro Tips The Touchpad display turns off on its own after specified allotted time of inactivity (Auto sleep display setting). It will turn back on when the screen is touched, or for some alarm conditions. The screen can also be turned off manually by pressing "Sleep." The Touchpad volume can be changed in the Settings screen.
- Page 11 THIS PAGE IS INTENTIONALLY LEFT BLANK...
-
Page 12: Specifications
(2) This device must accept any interference, including including interference that may cause undesired operation. interference that may cause undesired operation of Changes or modifications not expressly approved by Alula could the device. void the user’s authority to operate this equipment.
Need help?
Do you have a question about the RE657WF and is the answer not in the manual?
Questions and answers