Important Safety Notes; Operation - Intimus 240 Crusher Operating Instructions Manual

GB
<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the destruction process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of this
machine does not provide for any guarantee
regarding hazard-free operation by children.
Sequence of Auto Mode Operation
1. Press the "Power Switch" to "ON". The Blue
and Green lamps illuminate briefly, the Yel-
low lamp flashes and the destruction wedge
returns to home position.
2. Open door and place the hard drive(s) on the
Support Rails.
Note: Center the hard drive between right and
left Support Rails and ensure the hard drive(s)
are pushed to the back (Laptop drives can be
oriented perpendicular to the standard drive
orientation to mount on both support rails). The
Green light will illuminate when the hard drive(s)
are detected by the auto-sizing sensors located
on the back wall of the destruction chamber.
3. Close the door and press the "Size" button.
Notes:
a) The crusher will automatically size the
hard drive(s) and lower the wedge to just
above the hard drive and stop. This will
happen only on the first hard drive or until
the "Size" button is pressed again or the
crusher is powered off.
b) Pressing the "Size" button at anytime du-
ring auto mode operation will return the
destruction wedge to the home position
4. Press the "Destroy" button. The crusher will
destroy the media in the destruction chamber
in a pre-set cycle and return to the previously
set position to be ready to destroy the next
piece of media of the same size.
5. Open the door and remove the hard drive(s)
when the Green light illuminates, indicating
the destruction process is complete.
6. Insert media and close the door and repeat
from Step 4 until the job is complete or repeat
from Step 3 if a different height media is in-
serted in the chamber.

IMPORTANT SAFETY NOTES

<< Do not attempt to handle the hard drive
<< In case of danger switch the machine off
<< Always unplug the machine from the mains

OPERATION

Sequence of Manual Mode Operation
1. Press the "Power Switch" to "ON".
2. Press and hold the "Size" button for three
seconds or until the Green, Yellow and Blue
lights illuminate in a chasing sequence.
3. Open the door and place the Hard Drive(s)
on the Support Rails.
4. Press the "Size" button once to lower the De-
struction Wedge to level four, the uppermost
level. Press the "Size" button again to lower
the Destruction Wedge to the next lower level
and so on until the unit is sized to the desired
level for the destruction of the media in the
chamber. Notes:
a) The destruction wedge should be located
just above the media before the "Destroy"
button is pushed. Open the door and remo-
ve the hard drive(s) when the Green lamp
illuminates, indicating the destruction pro-
cess is complete.
b) The Yellow light will blink four times for le-
vel four, three times for level three and so
on. A total of four levels are available. After
the Destruction Wedge reaches level one,
the lowest level, the next push of the "Size"
button will return the Destruction Wedge to
the Home position.
5. Press the "Destroy" button.
Cleaning the Debris Tray
Open the door and remove the Hard Drive(s)
after the destruction wedge returns to the top
position and the motor stops.
As a safety precaution, do not open the door
until the destruction wedge has returned to the
topposition and the motor has stopped.
After the crusher destroys the Hard Drives, small
fragments of the hard drive may be left on the
Support Rails and will be left in the Debris Tray.
Sweep or vacuuming the fragments from the
Support Rails into Debris Tray located on the
bottom of the Destruction Chamber in between
the Support Rails of the crusher. When enough
debris has accumulated, remove the Debris Tray
and empty it. Place the Debris Tray back in and
resume the destruction process.
Note: Make sure that the Debris Tray is inserted
all the way to the back of the chamber or the
door will not shut completely.
000234
Translation of the Original Operation Manual
during a destruction phase! Danger of
injury!
with the mains switch, or with the emer-
gency switch, or unplug the machine!
power supply before opening the machine!
Repairs may only be performed by trained
personnel!
4
Übersetzung der Originalbetriebsanleitung
INITIATION
INTRODUCTION
The crusher model intimus 240 Crusher will
physically destroy working and non-working
hard disk drives (HDD), network HDD, half-
height HDD, standard HDD and laptop HDD by
deforming the data platters, pc board and frame
of the hard drive.
INSPECTION
Unpack the shipping carton/case and take out
the crusher. Inspect the crusher for shipping da-
mage as soon as it is unpacked. If the crusher or
any accessories are damaged or fail to operate
correctly, notify carrier and contact your dealer
immediately.
INSTALLATION
Power Plug
Confirm power requirements as indicated on
label located on back of crusher. Plug the IEC
connector attached to the power cord supplied
into the receptacle on the back of the unit.
Always unplug the unit from the
mains power supply before opening
the machine!
Location
The crusher must be placed on a flat, hard and
secure horizontal surface. Do not use the crus-
her on uneven or unstable surfaces.
INSTRUCTIONS FOR USE
Operating Environment
Please do not use or keep the crusher in envi-
ronments with excessive heat, cold, humidity, or
dust.
Use caution when bringing the crusher from a
cold environment into a warm environment. If
moisture has accumulated due to a sudden
change of temperature, wait (1) hour before ope-
rating the crusher.
Cleaning
Please wipe dirt off with a soft and dry cloth. Do
not use chemicals or solvents.
When cleaning the unit, make sure that the po-
wer is not connected, and wipe with a soft and
dry cloth.
To achieve proper hard drive placement, sweep
or vacuum Hard Drive debris from the inside of
the crusher. Empty debris from the Debris Tray
and remove any debris that has remained on the
Support Rails. Excess debris will alter the place-
ment of the HDD and may cause damage to the
crusher.
DISPOSING
DISPOSING OF THE MACHINE:
Dispose of the machine in an environ-
mentally sound fashion at the end of its
useful service life. Do not dispose of any
of the parts included in the machine or
its packaging with household trash.
94919 2 07/18