Important Safety Notes; Operation - Intimus 120 CC3 Operating Manual

USA

IMPORTANT SAFETY NOTES

<< The machine may not be operated by more
than one person at any given time!
The machine was designed for safe operation
by "one person only".
<< During the shredding process no other
work may be performed on the machine
(for example cleaning, etc.)!
<< The machine is not a toy, and is not suitable
for use by children!
The overall technical safety concept of
this machine (dimensions, feed openings,
emergency shutdown devices etc.) does not
provide for any guarantee regarding hazard-
free operation by children.
Warning:
Moving parts can crush and cut!
CONTROLS:
1 = Mains plug (Fig. 2)
When the machine is first plugged in it is
not on.
2 = Function buttons (Fig. 1)
"Ready"/ "Off" / "Stop"
This button has three functions:
a) "Ready"
The machine changes to "Ready" if you
press this button briefly.
At the same time the integral LED
display comes on.
b) "Off"
The machine switches off if it is in the
"Ready" mode and the button is held
down for about 3 seconds.
Note: The machine
automatically if it is not used for about 5
minutes.
c) "Stop"
If you press this button briefly when the
cutters are running they switch off and
stop.
3 = Forwards button (Fig. 1)
This button has two functions:
a) If this button is pressed briefly, the
cutting mechanism runs forwards for a
few seconds, e.g. to remove remaining
material from the cutting mechanism.
6
7
8
2
Fig. 1
<< Danger of injury! Never insert fingers into
opening!
<< In case of danger switch the machine
off with the mains switch, or unplug the
machine!
<< Always unplug the machine from the mains
power supply before opening the machine!
Repairs may only be performed by trained
personnel!
Warning:
Electrical Hazard!
At the same time the integrated LED
display
b) If this button is pressed and held
for approx. two secs., the cutting
mechanism runs forwards continually
and materials to be shredded can be fed
into the machine. At the same time the
integrated LED display
4 = Reverse button (Fig. 1)
If you press this button the cutters run
backwards for a short time. At the same
time the integral LED display
5 = Light barrier (Forward motion) (Fig. 3)
The shredding procedure starts as soon
as material is fed into one of the two feed
slots. At the same time the integral forward
switches off
button LED display
6 = Control display (Fig. 1)
"Material
"Simultaneous material feed" / "Light
barrier covered when door opens or
when machine turned on"
For the procedures see the relevant
description under the "MALFUNCTION"
section.
a) "Material jam in machine"
Comes on when too much material has
been fed into the cutters. The cutters
jam, then run in reverse for a short time
and stop. The motor switches off.
3
9
10
1
11
4
<< Danger of injury! Keep all loose
articles of clothing, ties, jewe-
lery, long hair or other loose
objects away from opening!

OPERATION

lights up.
lights up.
comes on.
comes on.
jam in machine"/
Fig. 2
2
120 CC3/CC4/CC5/CC6
INITIATION
AREA OF APPLICATION:
The intimus 120SC2/CC3/CC4/CC5/CC6
shredder is a machine used for shredding general
documents and data carriers such CD's, DVD's, credit
cards and 3.5" diskettes.
The machine must only be used to
shred paper, credit cards and CD's,
DVD's and 3.5" diskettes.
Shredding other sorts of data carriers
may cause damage to the machine (e.g.
damage to the cutters etc.).
INSTALLATION:
- Unpack the machine and put it together.
- Fit the plastic bag onto the bag frame.
- Attach the Power Cord to the Power Connection on
the machine and plug into an AC outlet (1) (Fig. 2)
(For information on the right fuse for the plug see
"TECHNICAL DATA").
The socket outlet shall be installed
near the equipment and shall be
easily accessible!
Only operate the machine in enclo-
sed rooms at temperatures between
10°C and 25°C!
Keep enough distance to the sur-
roundings when installing the ma-
chine.
b) "Simultaneous material feed"
Comes on when material has been fed
into both slots at the same time. The
cutters stop, then run in reverse for a
short time and stop. The motor switches
off.
c) "Light barrier covered
when door open"
Comes on when there is still material in
one of the two feed slots when the door
is opened. The cutters stop. The motor
switches off.
d) "Light barrier covered
when machine turned on"
Comes on when there is still material
in one of the two feed slots when the
machine is switched on.
7 = Control display (Fig. 1)
"Oil cutters"
Comes on when the cutters in the cross
cut version must be oiled. The lubrication
procedure must be acknowledged on
the reverse button (4) (see description in
"CUTTER MAINTENANCE").
12
13
Fig. 3
120 SC2
data
5