1.3 Limitation of liability You have made a good choice by purchasing the All information and notes in these operating instructions UNICRAFT crane scale. were summarised while taking applicable standards and rules, the state-of-the-art technology and our long-term Please read the operating instructions thoroughly before knowledge and experiences into consideration.
Safety Obligations of the operating company WARNING! If the crane scales is used for commercial purposes, the This combination of symbol and signal words indi- operating company of the crane scales must comply with cates a potentially dangerous situation which may the legal working safety regulations.
Safety 2.3 Requirements to staff 2.4 Personal protective equipment Qualifications The personal protective equipment serves to protect per- sons against impairments of safety and health while wor- king. The staff member has to wear personal protec-tive The different tasks described in this manual represent equipment while performing different tasks on and with different requirements to the qualification of the persons the machine which are indicated in the individual para-...
Safety 2.5 General safety regulations If it is necessary to remove any safety devices for fitting, repair or maintenance work, they must be re-installed im- mediately after maintenance or repair is complete. HINWEIS! 2.7 Tests All local regulations (the latest valid version) which apply in the country where the device is used must be Lifting equipment is a testable suspension.
Intended use Intended use Technical Data The Crane scale is used solely to weigh free moving KW 50 KW 100 loads on the crane. The Crane scale may only be opera- ted by persons trained on the machine. Maximum load...
The equipment must not be used in the open air if it is rai- ning. 4.2 Power Model Max. Min. Ca- Reso- Area Capacity pacity lution Fig. 2: Type plate of the Crane scale KW 50 KW 50 5,000kg 40kg 2,500 Transport, Packaging, Storage KW 100 10,000kg 100kg 2,000 4.3 Dimensions 5.1 Transport...
Description of device Description of device Service 6.1 Illustration DANGER! Danger to life due to falling of the load! Falling loads can cause serious injury or even death. - Never step under suspended loads, stay there or work under suspended loads. - Move loads only under supervision.
Service 7.2 Functions ATTENTION! Buttons - Loads may not be drawn at an angle. - Do not lift loads exceeding the maximum load capa- Designation/ Functions city of the Crane scale (see type plate). Symbol - Fixed or jammed loads must not be lifted with the On-Off Press 1 sec.
Page 11
Service Key / Label Functionality Report stands for Annotation Clear Delete the last weight. Power cut Use this button to clear all OVerLoaD weights. Overload Scroll digitally to the left. 2nd function View accumulated weight. View Using the battery power HOLD The scale is locked.
Operation Operation Locking / unlockingif you want to lock the scale. The symbol Step 1: Press , if you want to lock the HOLD 8.1 Operators scale. The Symbol shines. a) The balance should be stable, otherwise the symbol will bel displayed.
Operation Delete (all entries) Step 1: If you press and avctivate ATTENTION! then all weights will be deleted. When the Sym- lights up, it means that all weights The resolution circuit changes the overload range of the scale. For example, if a 3000 * 1kg resolution is changed are cleared.
Operation Display NOTE! The "automatic shutdown" can be set to the following ATTENTION! values: 0 (never), 5 min, 15 min, 30 min, 60 min. The "display" function allows you to choose between different qualities of the display presentation as long as the scale is in motion.
Care, Maintenance and Repair Step 3: First, lift the load only a short distance and check 1. The battery is permanently attached to the battery that the load is stable. compartment. To remove the battery, remove two screws on the access door, pull the battery straight Step 4: Lift the load steadily and evenly and read the in- out, and disconnect the battery cable from the scale.
Care, Maintenance and Repair Visual inspection Maintenance Maintenance work interval A [mm] Before every Check Crane scale for damage. B [mm] C [mm] Check the battery level before each D [mm] E [mm] Regularly inspect the Crane scale, including lifting eye and load hook for F [mm] deformation, cracks or other defects.
Check the crane scale 10 Check the crane scale The use of the crane scales is possible after: UVV "Winches, Hoists and Pulling Devices" DGUV regu- lation 54, UVV "Krane" DGUV regulation 52-Testing in accordance with DGUV regulation 54 (BGV D8 § 23 (VBG 8 §...
Troubleshooting 11 Troubleshooting Disorder Possible cause Solution No indication after switching on Battery defective or not charged Charge or replace the battery Display flashes continuously. Battery voltage too low Charge or replace the battery Tare function does not work. Tare-Button defective Clean or Crane scale for repair Display does not show [0] after Tare set?
13 Spare parts Example: The load hook for the Crane scale must be ordered. DANGER! - Type of device: Crane scale KW 50 Danger of injury by the use of wrong spare - Item number: 6171405 parts! - Position number: 8...
Stürmer Maschinen GmbH Dr.-Robert-Pfleger-Str. 26 D-96103 Hallstadt herewith declares that the following product Product group: Unicraft® Werkstatttechnik Type of machine: Crane scale Designation of the machine: KW 50 KW 100 Item number: 6171405 6171410 Serial number: ______________________ Year of manufacture: 20_____ complies with all relevant provisions of the above-mentioned Directive as well as the other applicable Directives (hereafter), including any changes in force at the time of declaration.
Maintenance plan 16 Maintenance plan Maintenance plan 40 h 200 h Requirement yearly Date Operating hours Employee Signature KW-Series | Version 1.03...