Telrad CPE12350 User Manual 1. About this Manual The content of this User Manual has been made as accurate as possible. However, due to continual product improvements, specifications and other information are subject to change without notice. 2. Product Overview This CPE supports LTE B42/43/48/46 (Subject to the configuration of LTE module) and it supports popular operating systems like Windows, Linux and Mac.
Telrad CPE12350 User Manual Figure 3-1-1 Login 4. Home page 4.1 LTE There are 6 function on this page, they are “Overview”, ”ND & S” , ”PLMN Selection”, “eNB Settings”, “Bearer Settings”, “PIN Management” Figure 4-1-1 LTE 4.1.1 Overview There are more LTE information on this page, they are “Serial Number”, “IMEI”, “IMSI”, “Supported Band”, “Firmware version”...
Telrad CPE12350 User Manual Figure 4-1-1-1 Overview 4.1.2 ND&S On this page include “Uplink QAM64”, “Scan Mode” and “Band” Figure 4-1-2-1 ND&S Uplink QAM64: Enable/Disable Scan Mode: Full band/Dedicated Earfcn Band: Supported Band selection (Default band is 46) 4.1.3...
Telrad CPE12350 User Manual Figure 4-1-3-1 PLMN Selection Network Mode: there are two modes Nomadic, Mobile Allow Roaming: If “allow roaming” is checked, then CPE first selects eNBs from the Home/ Equivalent PLMN-IDs, Otherwise If not available, it tries connection to “any” PLMN-ID.
Telrad CPE12350 User Manual Figure 4-1-4-1 Bearer Settings 4.1.5 PIN Management From this page, you can see the USIM card status and PIN status. The default PIN status is disabled; you can input the correct PIN to enable the PIN function. The maximum PIN attempts are 3, otherwise you must enter PUK to reset the PIN code.
Telrad CPE12350 User Manual Figure 4-2-2-1 Internet Connection Mode: Route/NAT, L2 Bridge(GRE), L3 Bridge NAT: Default Enable MGMT and Date Interface: Combine/ Separate 4.2.3 On this page, include “LAN Reset”, “Device IP” and “DHCP” Figure 4-2-3-1 LAN LAN Reset: ...
Telrad CPE12350 User Manual 4.2.4 A virtual private network (VPN) is a point-to-point connection across a private or public network (Internet). VPN Passthrough allows the VPN traffic to pass through the router. Thereby we can establish VPN connections to remote network.
Telrad CPE12350 User Manual Figure 4-3-1-1 Port Forwarding 4.3.2 From this page, you can configure a De-militarized Zone (DMZ) to separate internal network and Internet. Figure 4-3-2-1 DMZ DMZ Enable: Default value is Disable DMZ Host IP address: The IP address of your PC.
Telrad CPE12350 User Manual Figure 4-4-1-1 Device Management 4.4.2 TR069 On this page, include “TR069 Enable” and “TR069 Configuration” Figure 4-4-2-1 TR069 TR069: Default value is Enable ACS Interface: Default value is “lte0pdn0” ACS Port: Default value is “7547”...
Telrad CPE12350 User Manual Re-enter Password: Default value is “cwmp” 4.4.3 SNMP On this page, include “Snmpd”, “ Snmpd Read Only Community”, “ Snmpd Read Write Community”, you can change setting by manual. Figure 4-4-3-1 SNMP Snmpd: Default value is Enable Snmpd Read Only Community: ...
Telrad CPE12350 User Manual Figure 4-5-2-1 Config Management 4.5.3 Firmware Update On this page, you can upgrade the current Router version from the local PC. 30s is needed to complete the whole upgrade process, and then the device will reboot automatically.
Telrad CPE12350 User Manual 4.6.2 Iperf On this page, you can use the page of “iperf”, test throughput function. Figure 4-6-2-1 Iperf Status: Default value is “Enable” Server Address: Default value is “8.8.8.8” Server Port: Default value is “5001”, the range is 1024~65535 Management Port: ...
Telrad CPE12350 User Manual 5.1.3 Special Features : RJ45 1 Giga Ethernet Ports with passive PoE PIN enabled(56V) USIM interface One USIM interface under the cover Ethernet Protocol 10/100/1000Mb protocol IP Routing TCP,UDP,ICMP,ARP General DHCP,NAT/NATP Power supply Passive POE Max power consumption 56V / 0.45A...
Telrad CPE12350 User Manual 6.1.2 To mount the CPE to wall To mount the CPE to wall, follow the steps below: To mount the CPE to wall Figure 6-1-2-1 6.1.3 Install the USIM card: This CPE is specially designed for the 4G LTE network. Please check that you have a valid USIM card from the service provider.
Telrad CPE12350 User Manual Install the USIM card Figure 6-1-3-1 6.1.4 Product Shipping Package Main Lable On Main Label, you can see IMEI/MAC/SN on it. Figure 6-1-4-1 Main Label 7. Revision History Author Revision Changes Date Fhan Create Draft 2020-11-04...
Page 20
Telrad CPE12350 User Manual FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 21
Telrad AOL-TE7863 User Manual limits, The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 35 cm from all persons during the normal operations. IC STATEMENT This device complies with Industry Canada license-exempt RSS standard(s). Operation is...