IP SPEED DOME CAMERA
Quick Start Guide
46235.030D
① Pull the cables through the
② Secure the speed dome to the
■ Please read this instruction carefully before operating the
bracket. Mount the speed dome
bracket with the screws.
unit and keep it for further reference.
to the bracket.
Telecamera Speed Dome IP 4Mpx (2560 × 1440 30fps), obiettivo 4.7 - 141 mm,
■ All the examples and pictures used here are for reference
filtro IR meccanico, zoom ottico 30x, illuminatori IR con portata fino a 100m, slot
only.
SD CARD 256GB, funzioni di analisi video WDR e 3DNR, RTSP, gestione allarmi
■ The contents of this manual are subject to change without
1IN/1OUT, alimentazione PoE+ (IEEE 802.3at) o 24 Vdc max 30 W, completa di
staffa da parete e alimentatore, grado di protezione IP66. Dimensioni senza staffa
notice.
ø 209x328 mm. Peso 3700 g.
1. Interfaces and Parts
Contenuto della confezione
③ Drill the screw holes on the wall
④ Fix the two screws to the holes
Una volta ricevuto il dispositivo, controllare gli accessori indicati di seguito. Le illu-
according to the drill template.
as indicated by the arrows (left)
strazioni sotto riportate hanno solo funzione di riferimento. Far riferimento all'appa-
Then insert the plastic plugs into
and leave 12mm clearance.
recchiatura in dotazione.
the holes.
Telecamera
Camera
8
Panoramic Bullet
Network Camera
Quick Start Guide
* TVI/AHD output can be controlled by
⑤ Connect the cables and then
⑥ Fix the bracket to the wall with
refully before using the product
four screws.
dial switch.
hang the bracket on the wall .
Introduzione
used here are for reference only.
2
Questa telecamera IP Speed Dome è stata progettata per fornire soluzioni TVCC
2. Installation
re subject to change without
ad elevate prestazioni. Adotta chip di elaborazione video allo stato dell'arte. Utilizza
le tecnologie più avanzate di codifica e decodifica video ed è conforme al protocollo
TCP/IP, SoC (System on Chip) per assicurare la stabilità e l'affidabilità del sistema.
Please make sure the wall is strong enough to bear the dome
I manuali completi e i software CVM, Iptool.exe e Diskcalculator.exe sono disponi-
camera's weight. Please make sure the camera is powered off
bili nella scheda prodotto consultabile nel sito www.vimar.com
during installation.
Connessioni
aution
Di seguito sono riportate le principali connessioni della telecamera.
◆ Install SD Card
operly, please contact your dealer
er attempt to disassemble the
responsible for any problems
maintenance.)
rusion into the camera.
ust be strict compliance with the
e nation and region. When the
ling, the device shall be firmly
① Loosen the two screws
of the cover of the dome.
cified voltage range.
ect it to physical shock.
uct is recommended to be
eliability of the camera.
s.
use clean cloth to wipe it gently.
n or extra bright place.
mely hot, cold, dusty or damp
gh electromagnetic radiation.
ood ventilation is required for
Installazione scheda SD e collegamento dell'alimentazione
Installare la scheda di archiviazione:
1 - Allentare le viti di fissaggio del coperchio posteriore come illustrato di seguito
(Fig. 1).
2 - Inserire la scheda SD nello slot della scheda di archiviazione (Fig. 2).
3 - Rimontare e fissare il coperchio posteriore.
Installazione telecamera
Prima di iniziare, assicurarsi che la parete sia sufficientemente solida
per sopportare il peso della telecamera. Installare la telecamera
in ambiente asciutto. La procedura di montaggio è la seguente:
1- Passare i cavi attraverso la staffa. Montare la speed dome sulla staffa (Fig. 3).
2- Fissare la speed dome alla staffa con le viti (Fig. 4)
3- Utilizzare la dima di foratura per praticare i fori per le viti sulla parete (Fig. 5).
4- Allineare le due viti ai fori indicati dalle frecce e lasciare circa 12 mm dal muro
(Fig. 6)
5- Collegare i cavi e quindi appendere la staffa al muro e fissarla (Fig. 7-8).
49401711A0 00 2107
Alarm Connection:
1. Alarm Input
a) There are four independent alarm input ports ALM-INx (x=A~D)
and one grounding port (ALM-GND).
b)Alarm input(NO type): Connect DC5V~DC12V voltage
between the alarm input port ALM-INx and the grounding port
(ALM-GND).
c) Alarm input(NC type): Disconnect the voltage between the
alarm input port ALM-INx and the grounding port (ALM-GND).
2. Alarm Output
1
① Network interface
2
a) Support 1CH alarm output including OPEN, COM
3
connections.
② HP audio output
4
b) Alarm output: One passive switch for user to connect alarm
5
Istruzioni per l'uso
③ MIC IN
devices; the alarm output state will be auto on/off according to
6
Quick start guide
7
your setting.
④ Alarm input/output
⑤ Power
Connecting Network Cable
⑥ RS485
⑦ Video (TVI/AHD)
Camera
Quick start guide
output
⑧ Grounding
1
CD
Drill template
Screwdriver
Rubber plug
3
Overview
Insert SD card
1
2
3
4
5
6
② Open the cover and insert
SD card.
1
1 - Interfaccia di rete / Network interface
2 - Uscita audio HP / HP audio output
3 - Ingresso MIC / MIC IN
4 - Allarmi In/Out / Alarm input/output
5 - Alimentazione / Power
8 9
6 - Massa / Grounding
* 1
It is recommended to install the security cap for outdoor installation.
* 2 This camera can be powered by DC 12V/PoE power supply. If the PoE switch
is used to power the camera, DC12V power supply is not required.
ALM-INA
ALM-INB
ALM-INC
ALM-IND
ALM-GND
Power
ALM-OPEN
Install the Speed Dome
◆
ALM-COM
RS 485 A
RS 485 B
Speed Dome IP 4Mpx camera (2560 × 1440 30fps), 4.7 - 141 mm lens, mechanical
IR filter, 30x optical zoom, IR illuminators with a capacity of up to 100m, 256GB SD
CARD slots, WDR and 3DNR video analysis functions, RTSP, 1IN/1OUT alarm ma-
nagement, PoE+ power supply (IEEE 802.3at) or 24 Vdc max 30 W, complete with
wall bracket and power supply, IP66 protection degree. Dimensions without bracket
ø 209x328 mm. Weight 3700 g.
Package content
① Pull the cables through the
After you receive your device, please check the following accessories. The pictures
bracket. Mount the speed dome
here are for reference only.
to the bracket.
Dima di foratura
Drill template
4 tapping screws
2
3
③ Drill the screw holes on the wall
×4
Plastic plug
according to the drill template.
Introduction
Then insert the plastic plugs into
3
This Speed Dome IP-camera is designed for high performance CCTV solutions. It
the holes.
adopts state of the art video processing chips. It utilizes most advanced technolo-
●
gies, such as video encoding and decoding technology, complies with theTCP/IP
Alarm Input
protocol, SoC (System on chip), etc to ensure this system more stable and reliable.
Complete manuals and CVM, Iptool.exe e Diskcalculator.exe software are available
to download in the Product info sheet section of www.vimar.com website.
Connections
Alarm Output
Here below the main connections of the camera
1
2
●
3
4
5
⑤ Connect the cables and then
6
hang the bracket on the wall .
7
1
Ethernet Connector *
2
Audio Input (MIC)
① Loosen the nut from the main element.
3
Audio Output (HP)
② Run the network cable (without RJ 45 connector) through the
4
Alarm Input/Output
both elements. Then crimp the cable with RJ 45 connector.
5
RS485
③ Connect the cable to the E
6
Power Connector *
nut and the main cover.
7
Ground
8
Reset
9
Micro SD Card Slot
Install SD Card and Power Connection
Install Storage Card:
Please make sure that the wall or ceiling is strong enough to
1 - Loosen the fixed screws of the rear as shown below (Fig. 1).
withstand 3 times the weight of the camera.
2 - Insert the SD card into the storage card slot (Fig. 2).
① Open the cover of the camera and then insert a micro SD card.
3 - Install back the cover back.
Then install back this cover and fix it firmly with the screws (please
Camera Installation
keep it flat when installing).
Before start, please make sure that the wall is strong enough to withstand
the weight of the camera. Please install the camera in the dry environment. The
mounting steps are as follows:
1- Pull the cables through the bracket. Mount the speed dome to the bracket (Fig.
3).
2- Secure the speed dome to the bracket with the screws (Fig. 4).
3- Drill the screw holes on the wall according to the drill template (Fig. 5).
4- Drive the two screws to the holes indicated by the arrows and leave 12mm
clearance (Fig. 6).
5- Connect the cables and then hang the bracket on the wall and fix it (Fig. 7-8).
② Secure the speed dome to the
bracket with the screws.
Viti e tasselli
Screws and Plastic plug
④ Fix the two screws to the holes
as indicated by the arrows (left)
and leave 12mm clearance.
Connecting Alarm Input/Output
ALARM-INA
3
IPC
ALARM-GND
4
ALARM-COM
1
IPC
+
ALARM-OPEN
2
Power Source
Connecting Network Cable
Descrizione/
Description
1
ALARM-OPEN
⑥ Fix the bracket to the wall with
2
ALARM-COM
Power
four screws.
3
ALARM-GND
4
ALARM-IN 1
2
2
1
connector. Then tighten the
thernet
4
Installation
3. Connections
Alarm Connection:
Alimentatore
1. Alarm Input
Power supply
a) There are four independent alar
and one grounding port (ALM-GN
b)Alarm input(NO type): Connec
between the alarm input port ALM
(ALM-GND).
1--ALM-COM
2--ALM-OPEN
c) Alarm input(NC type): Disconn
3--ALM-INA
4--ALM-GND
alarm input port ALM-INx and the g
RS485T+
RS485T-
2. Alarm Output
a) Support 1CH alarm output incl
connections.
b) Alarm output: One passive swi
devices; the alarm output state wil
Sensor
your setting.
Connecting Network Cable
+
Alarm
-
-
1
5-12 Vdc
-
+
3
Contatti N.O./
Contacts N.O.
Viale Vicenza, 14
36063 Marostica VI - Italy
www.vimar.com
Power
2
3
Need help?
Do you have a question about the Elvox 46235.030D and is the answer not in the manual?
Questions and answers