Protecting The Environment; Maintenance - DeWalt D36000 Original Instructions Manual

English
Transporting (Fig. O, Z)
The detachable parts can be stored in the water basin for easy transportation.
1. Drain the water basin. See Maintenance.
2. Remove the edge guide and the extension table.
3. Lock the cutting cart in position.
4. Remove the water collectors.
5. Lift the machine out of the water basin as shown.
6. Place the collectors into the water basin in the orientation as shown.
7. Turn the water basin upside down.
8. The edge guide and the extension table can be placed in the water basin before nested.
9. Lift and hold the machine at the carrying points

WARNING: When carrying the machine, always seek assistance. The machine is
too heavy for one person to handle. Always lock the cutting cart before moving or
transporting saw.

MAINTENANCE

Your power tool has been designed to operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation depends upon proper tool care and
regular cleaning.

WARNING: To reduce the risk of serious personal injury, turn tool off and
disconnect tool from power source before making any adjustments or removing/
installing attachments or accessories. An accidental start‑up can cause injury.

WARNING: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by a D
authorized service centre. Always use identical replacement parts.
If the supply cord is damaged, it must be replaced only by D
service organisation.
Draining the Water Basin (Fig. ###)
The water basin must be drained after each use.
1. Place a suitable container under the drain plug
2. Remove the drain plug.
3. Allow ample time for the liquid to drain.
4. After the liquid has been drained, re-install the drain plug.
5. Dispose of the liquid with due care for the environment.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning

WARNING: Blow dirt and dust out of the main housing with dry air as often as dirt is seen
collecting in and around the air vents. Wear approved eye protection and approved dust
mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals for cleaning the non‑metallic
parts of the tool. These chemicals may weaken the materials used in these parts. Use a
cloth dampened only with water and mild soap. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid.
Before use, carefully check the cutting disk cover to determine that it will operate properly.
Ensure that mud, or work-piece particles cannot lead to blockage of one of the functions.
In case of workpiece fragments jammed between cutting disc and guard disconnect the
machine from the power supply and follow the instructions given in section Mounting the
cutting disc. Remove the jammed parts and reassembling the cutting disc.
Keep the ventilation slots clear and regularly clean the housing with a soft cloth.
The following cleaning operations must be performed every day.
1. Insert the water pump into a bucket of clean water and pump the water through the
hose system.
2. Wipe the rails and support arm with a grout sponge or a rag.
3. Spray the water basin and the sliding table with clear water. Wipe any dust residue away
with a grout sponge.
Optional Accessories

WARNING: Since accessories, other than those offered by D
with this product, use of such accessories with this tool could be hazardous. To reduce the
risk of injury, only D WALT recommended accessories should be used with this product.
e
Consult your dealer for further information on the appropriate accessories.
Stand
D240001 Heavy Duty Tile Saw Stand
Range of Cutting Discs Available
DT3734 Wet tile diamond saw blade for cutting ceramic, porcelain tiles and stone
DT3733 Wet tile diamond saw blade for cutting tiles
10
61 as shown in Fig. N.
WALT factory service centre or a D WALT
e e
WALT or an authorised
e
58 .
WALT, have not been tested
e
Storage
Store the equipment and accessories out of children's reach in a dark and dry place at above
freezing temperature. The ideal storage temperature is between 5 °C and 30 °C.

Protecting the Environment

Separate collection. Products marked with this symbol must not be disposed of with
w
normal household waste.
Products contain materials that can be recovered or recycled reducing the demand
for raw materials. Please recycle electrical products according to local provisions.
Further information is available at www.2helpU.com.