Page 1
All manuals and user guides at all-guides.com Assembling CarTFT FleetPC-2 Remove all the screws as following:...
Page 2
All manuals and user guides at all-guides.com...
Page 3
All manuals and user guides at all-guides.com...
Page 4
All manuals and user guides at all-guides.com Remove the left cover Now you are able to remove the harddrive cover and set it apart for a while.
Page 5
All manuals and user guides at all-guides.com Remove the case cover...
Page 6
All manuals and user guides at all-guides.com Start to remove the Heatpipe. It is fixed with the following two screws ( Note: One end is shorter than the other one )
Page 7
All manuals and user guides at all-guides.com Pull the Headpipe out (in the direction of the arrows) Please do not use some tools to do this. If you just move the heatpipe a litte bit up and down, you will be able to remove it easily. Now, do the same on the other side.
Page 8
All manuals and user guides at all-guides.com Remove the IDE Cable Remove the ATX Cable. Remove the screws of the Mainboard.
Page 9
All manuals and user guides at all-guides.com Also remove the USB, Power and LED Cable...
Page 10
All manuals and user guides at all-guides.com Take the Mainboard out of the case and set it apart. At the bottom of the mainboard you will find the screws for the cooling unit. You have to remove this screws to place the CPU on the right place.
Page 11
All manuals and user guides at all-guides.com Remove the cooling unit at the top of the Mainboard. Insert CPU (there is only one possible way)
Page 12
All manuals and user guides at all-guides.com Fix the CPU on the showed screw Take the cooling pad and put it on the CPU...
Page 13
All manuals and user guides at all-guides.com Now, you can bring up the cooling unit back to the CPU and fix the screws...
Page 14
All manuals and user guides at all-guides.com Place the RAM to the slot in push it down till the RAM is engaged...
Page 15
All manuals and user guides at all-guides.com Put the mainboard back into the case and fix it.
Page 16
All manuals and user guides at all-guides.com Connect the ATX- and DIE-Cable with the mainboard Now, connect Power/LED- and USB-Cable...
Page 17
All manuals and user guides at all-guides.com (like you see on the pictures below) Connect the included SATA Cable Lead the other end of the SATA-Cable downwards (do not lead to much cable on the backside, because later it will stands in the way )
Page 18
All manuals and user guides at all-guides.com Connect the headpipe´s with the cooling unit...
Page 19
All manuals and user guides at all-guides.com VERY IMPORTANT! There must be cooling paste on the top of the cooling unit to.
Page 20
All manuals and user guides at all-guides.com...
Page 21
All manuals and user guides at all-guides.com Set up the Cover of the enclosure back on the top...
Page 22
All manuals and user guides at all-guides.com Fix the covers of the Heatpipes...
Page 23
All manuals and user guides at all-guides.com...
Page 24
All manuals and user guides at all-guides.com...
Page 25
All manuals and user guides at all-guides.com You can assamble the System with, for example, a CF–Card (The slot for this card is on the backside.)
Page 26
All manuals and user guides at all-guides.com Fix the Harddrive as following:...
Page 27
All manuals and user guides at all-guides.com...
Page 28
All manuals and user guides at all-guides.com Connect the Harddrive with the SATA-Cables. Now you can screw the bottom of the enclosure.
Page 29
All manuals and user guides at all-guides.com Remove the isolation from the Powercables. Connect Keyboard, Monitor and your other external devices.
Page 30
All manuals and user guides at all-guides.com Now you can run your System and install the operating system, you like.