Quick Start Guide Foreword General This manual introduces the functions, installation and operations of the camera. Safety Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, WARNING could result in slight or moderate injury.
Page 3
Quick Start Guide manual. Please contact customer service for the latest program and supplementary documentation. There might be deviations in the description of the technical data, functions and operations, or errors in the print. If there is any doubt or dispute, we reserve the right of final explanation. Upgrade the reader software or try other mainstream reader software if the manual (in PDF ...
Quick Start Guide Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. The power supply must conform to the requirements of ES1 in IEC 62368-1 standard and be no higher than PS2.
Page 5
Quick Start Guide Do not touch the image sensor (CMOS) directly. Dust and dirt could be removed with air blower, or you can wipe the lens gently with soft cloth that is moistened with alcohol. You can clean the device body with soft dry cloth, and for stubborn stains, use the cloth with ...
Quick Start Guide Introduction Cable Waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For detailed operation, see FAQ manual. Figure 1-1 Cables Table 1-1 Cable information Port Name Description Power input Inputs 12 VDC power.
Quick Start Guide Port Name Description Ethernet Port Connects to network with network cable. Provides power to the device with PoE. PoE is available on select model. Audio input Connects to sound-pick-up device to receive audio signal. Audio output Connects to speaker to output audio signal.
Page 9
Quick Start Guide Figure 1-2 Alarm input Step 2 Connect alarm output device to the alarm output end of the I/O port. The alarm output is relay switch output, which can only connect to NO alarm devices. The ALARM_OUT port and the ALM_OUT_GND port with the same number constitute a switch for alarm output.
Quick Start Guide Network Configuration Device initialization and IP setting can be finished with the ConfigTool or in web page. For more information, see web operation manual. Device initialization is available on select models, and it is required at first use and after device is ...
Page 11
Quick Start Guide Enter username and password when you want to change IP, configure the system, update the device, restart the device, and more. Step 5 Click OK. Step 6 Select one or several devices in uninitialized status, and then click Initialize. Select the devices to be initialized, and then click Initialize.
Quick Start Guide Figure 2-3 Device initialization Step 9 Select Easy4ip or select Auto-check for updates as needed. If neither, leave them unselected. Click OK to initialize the device. Step 10 Click the success icon ( ) or the failure icon ( ) for the details. Click Finish.
Quick Start Guide Figure 2-4 Change IP address Select Static mode and enter start IP, subnet mask and gateway. Step 3 IP addresses of multiple devices will be set to the same if you select Same IP. If DHCP server is available in the network, devices will automatically obtain IP ...
Quick Start Guide Installation Packing List The tools required for the installation including electric drill are not provided in the packing. The operation manual and related tool are contained in the disk or the QR code. Figure 3-1 Packing list Dimension Figure 3-2...
Quick Start Guide Installing Device 3.3.1 Installation Method Figure 3-3 Installation Type Figure 3-4 Covering Mode Find the gap on the camera body; align it with the “TOP” on the corresponding quick mounting board, rotate the camera body clockwise to complete installation.
Quick Start Guide 3.3.2 Installing SD Card (Optional) SD card slot is available on select models. Please disconnect the power from the device before installing the SD card. Press the reset button for 10 seconds to reset the device. Figure 3-5 Install SD card 3.3.3 Attaching Device...
Quick Start Guide 3.3.4 Installing Waterproof Connector This part is only needed when a waterproof connector comes with the device and the device is used outdoors. Figure 3-9 Install waterproof connector...