Hoshizaki WOX-40WA-EW Instruction Manual

Hoshizaki WOX-40WA-EW Instruction Manual

Water electrolyzer
Hide thumbs Also See for WOX-40WA-EW:

Advertisement

Quick Links

WOX-40WA-EW
WATER ELECTROLYZER
INSTRUCTION MANUAL
FOR END USER
3-16 Minamiyakata, Sakae-cho, Toyoake, Aichi 470-1194 Japan
L1X006112 (111520)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WOX-40WA-EW and is the answer not in the manual?

Questions and answers

Summary of Contents for Hoshizaki WOX-40WA-EW

  • Page 1 WOX-40WA-EW WATER ELECTROLYZER INSTRUCTION MANUAL FOR END USER 3-16 Minamiyakata, Sakae-cho, Toyoake, Aichi 470-1194 Japan L1X006112 (111520)
  • Page 2: Important Safety Information

    * Do not damage the power cord or pull it in order to disconnect the electrolyzer from the electrical supply network. * If the supply cord is damaged, it must be replaced by your local Hoshizaki service agent or similarly qualified persons in order to avoid a hazard.
  • Page 3 In the context of this manual, the term "sanitizing water" refers to 2. CONSTRUCTION acidic water and "cleaning water" refers to alkaline water. [a] EXTERIOR 1. PRINCIPLE OF ELECTROLYSIS (Front) Flow of electrons DC Power Supply Sodium Hydroxide Hypochlorous Acid (HOCl) (NaOH) Electrolytic Cell...
  • Page 4: Checks Before Operation

    [b] OPERATION PANEL [1] Display select button Press this button to select the indication in the display on the operation panel. The lamp (green) of the selected item (clock, cell run time, current or voltage) illuminates. [2] Sensor button Press this button to use the dispensing sensor. Electrolyzed water is dispensed and stopped by the sensor while the lamp is on.
  • Page 5 IMPORTANT 2 cups Shake well If the power switch is turned off during a flush cycle, the unit cannot flush properly and may cause a clogged circuit. * When the flush lamp on the operation panel stops flashing and ✚ illuminates constantly, the unit starts a flush cycle.
  • Page 6 1) To adjust the current, press and hold the set button on the control 4) Press the set button. The display shows “0.00” (0:00). panel until the display shows “Adj.”. 5) Use the up/down button to indicate the desired start time in the 2) Press the set button.
  • Page 7: Maintenance

    [d] WATER LEAKS (DAILY) [a] EXTERIOR (AS REQUIRED) Check the unit and surrounding floor for water leaks. If any is found, contact an authorized Hoshizaki service company. The exterior is easily contaminated. Keep it clean. [e] EARTH LEAKAGE CIRCUIT BREAKER (MONTHLY) Note: The exterior surface is painted.
  • Page 8: Before Calling A Service Agent

    Restart the unit after water shall be effective for one year from the date of installation. water supply is resumed. Hoshizaki’s liability under the terms of the warranty are limited and supply Water supply Open. shall exclude routine servicing, cleaning, essential maintenance and/...
  • Page 9: Specifications

    14. SPECIFICATIONS Model WOX-40WA-EW Electrolysis System Membrane technology Electrolyte Salt containing at least 99% sodium chloride Power Supply 1 phase 220 - 240V, 50 - 60Hz Electric Consumption 170W / 170W Performance Sanitizing water: pH5.0 or less, available (Standard) *...
  • Page 10: Daily Inspection Sheet

    15. DAILY INSPECTION SHEET Make copies of this page. Date Time Sanitizing water Sanitizing water available chlorine concentration Salt level Water leaks around unit Drain [drain outlet (right)] Cell run time Current (A) Voltage (V) Checked by Date Time Sanitizing water Sanitizing water available chlorine concentration Salt level...

Table of Contents