Advertisement

Quick Links

Installation
Safety instructions for installation
Risk of damage from incorrect installation.
Incorrect installation can cause damage to the cooktop.
The cooktop must only be installed by a qualified person.
Damage from falling objects.
Take care not to damage the cooktop when fitting wall units or a rangehood
above it.
Fit the wall units and the rangehood before the cooktop.
The room in which the cooktop is installed must conform to all
relevant local and national building regulations and safety
regulations.
The veneer or laminate coatings of worktops (or adjacent kitchen
units) must be treated with 100 °C heat-resistant adhesive which will
not dissolve or distort. Any splashbacks must be of heat-resistant
material.
The cooktop must not be installed over a fridge, fridge-freezer,
freezer, dishwasher, washing machine, washer-dryer or tumble dryer.
A gas cooktop must not be installed directly next to a deep fat
fryer as the gas flames could ignite the fat in the fryer. It is essential
to maintain a distance of at least 300 mm between these two
appliances.
When installing the cooktop, make sure that the gas hose and
electrical connection cable cannot come into contact with hot
appliance parts.
The electrical cable and any flexible gas connection pipes must be
installed in such a way so that they do not come into contact with
any moving kitchen parts (e.g. a drawer), and cannot become
trapped.
Carefully observe the safety clearances listed on the following
pages.
11135230-03

Advertisement

Table of Contents
loading

Summary of Contents for Miele KM 3034-1

  • Page 1 *INSTALLATION* 11135230-03 Installation Safety instructions for installation  Risk of damage from incorrect installation. Incorrect installation can cause damage to the cooktop. The cooktop must only be installed by a qualified person.  Damage from falling objects. Take care not to damage the cooktop when fitting wall units or a rangehood above it.
  • Page 2 *INSTALLATION* 11135230-03 Installation Safety distances Safety distance above the cooktop A minimum safety distance must be maintained between the cooktop and the rangehood above it. See the rangehood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the rangehood, a minimum safety distance as per AS/ NZS 5601.1 must be maintained.
  • Page 3 *INSTALLATION* 11135230-03 Installation Safety distances to the sides and back of the appliance Ideally the appliance should be installed with plenty of space on either side. There may be a wall at the rear and a tall unit or wall on one side (right or left). On the other side, however, no tall unit or wall should stand higher than the appliance.
  • Page 4 *INSTALLATION* 11135230-03 Installation A gas appliance shall be installed such Clearance underneath the appliance that the surface temperature of any A minimum safety clearance of 15 mm nearby combustible surface* will not must be provided underneath the exceed 65 °C above ambient. appliance.
  • Page 5: Detailed Dimensions

    *INSTALLATION* 11135230-03 Installation Detailed dimensions Height of pan supports above the worktop surface a Vertical distance b Worktop surface c Pan support The vertical distance  from the top of the pan supports to the surface of the worktop is 57 mm.
  • Page 6 *INSTALLATION* 11135230-03 Installation Distances from burner to the edge of the appliance KM 3034-1 KM 3054-1...
  • Page 7: Installation Notes

    *INSTALLATION* 11135230-03 Installation Tiled worktop Installation notes Seal between the cooktop and the worktop Grout lines  and the hatched area underneath the cooktop frame must be smooth and even. If they are not, the cooktop will not sit flush with the worktop and the sealing strip ...
  • Page 8: Installation Dimensions

    *INSTALLATION* 11135230-03 Installation Installation dimensions All dimensions in this instruction booklet are given in mm. KM 3034-1 a Front b Building-in depth c Mains connection box with mains connection cable, L = 2,000 mm d Gas connection R ½ - ISO 7-1...
  • Page 9 *INSTALLATION* 11135230-03 Installation KM 3054-1 a Front b Building-in depth c Mains connection box with mains connection cable, L = 2,000 mm d Gas connection R ½ - ISO 7-1 e Electronics housing - maximum building-in depth 78 mm...
  • Page 10: Installation

    *INSTALLATION* 11135230-03 Installation Installing the cooktop Installation  Attach the sealing strip provided Preparing the worktop underneath the edge of the cooktop.  Create the worktop cut-out as shown  Feed the mains connection cable in the cooktop diagram. Remember down through the worktop cut-out.
  • Page 11 *INSTALLATION* 11135230-03 Installation Securing the cooktop Checking operation  After installing the cooktop, ignite all burners to check that they are operating correctly: - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.
  • Page 12: Gas Connection

    *INSTALLATION* 11135230-03 Installation Gas connection Check with your local gas supplier about the type of gas supplied and  Risk of explosion due to an compare this information with the incorrect gas connection. type of gas quoted on the If the gas connection is carried out appliance's data plate.
  • Page 13 Miele. Conversion to another type of gas is described in the section Connect the cooktop to the gas “Conversion to another type of gas”.
  • Page 14 *INSTALLATION* 11135230-03 Installation Setting the gas pressure For natural gas models The gas pressure must be set by the The gas regulator is only included with authorised gas fitter as shown on the appliances which are set up for data plate: connection to natural gas.
  • Page 15: Burner Ratings

    *INSTALLATION* 11135230-03 Installation Burner ratings Nominal ratings Burner Gas type Highest setting Lowest setting MJ/h MJ/h Auxiliary burner ULPG Semi-rapid burner ULPG Rapid burner ULPG Wok burner 17.0 ULPG 14.6 Total 42.8 ULPG 36.9...
  • Page 16: Electrical Connection

     Danger of injury! residual current device (RCD) with a trip range of 30 mA. Miele cannot be held liable for unauthorised installation, Replacing the mains connection maintenance and repair work as this cable can be dangerous to users.
  • Page 17: Conversion To Another Type Of Gas

    *INSTALLATION* 11135230-03 Conversion to another type of gas Jet table  Risk of explosion due to an incorrect conversion. The jet markings refer to a ¹/₁₀₀ mm If the conversion to another type of bore diameter. gas is carried out incorrectly, it may ...
  • Page 18: Changing The Jets

    *INSTALLATION* 11135230-03 Conversion to another type of gas Wok burner Changing the jets  Disconnect the cooktop from the electricity supply and turn off the gas supply. When converting to another type of gas, both the main and small jets need to be changed.
  • Page 19 *INSTALLATION* 11135230-03 Conversion to another type of gas  Secure the jets against inadvertent Changing the small jets loosening with sealing wax. To change the jets, the burner fixing screws must first be loosened and the upper section of the appliance removed.
  • Page 20 *INSTALLATION* 11135230-03 Conversion to another type of gas Checking operation  Check all gas fittings for leaks.  Reassemble the cooktop.  Ignite all burners to check that they are operating correctly. - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting.

This manual is also suitable for:

Km 3054-1Km 2354Km 2012

Table of Contents