Land Pride QH20 Series Operator's Manual page 12

Section 1: Assembly & Set-Up
Hook-up Without Floating Top Links
Refer to Figure 1-5:
1. Beginning with S/N 388293 and above, two
320-048D lower bushings (#3) are shipped tied to the
Land Pride Quick Hitch. Install these bushings onto
the implement's lower 7/8" hitch pins (#1) to provide
a tighter and more secure mounting.
2. Make certain implement's lower hitch pins (#1) are
secured in their respective clevis.
3. Place Quick Hitch release handles in the down
position as shown.
4. Lower tractor's 3-point lift arms until auto-lock hooks
are below implement's lower bushings (#3) and
upper hook is below upper hitch point (#4).
5. Carefully back tractor to align auto-lock hooks under
implement's lower bushings (#3) and upper hook
below upper hitch point (#4).
6. Slowly raise 3-point lift arms until auto-lock hooks
lock onto the implement's lower bushings and upper
hook captures implement's upper hitch point.
IMPORTANT: Make certain lower hitch pins are fully
seated in the auto-lock hooks and captured with lock
arms above. Also, make sure upper hitch point is
captured in the Quick Hitch upper hook.
IMPORTANT: When hooking-up a driveline, make
sure it is not too short to comply with shaft
overlapping guidelines. Refer to your implement
Operator's Manual for driveline hook-up instructions.
Replace driveline shafts and shields if they are too
short. See your nearest Land Pride dealer for new
shafts and shields.
7. If required, follow implement guidelines for driveline
hook-up and required driveline length.
Upper Hook
Release handle
10 QH15 Category l Hitch, & QH20 Category ll Hitch Quick Hitches 320-003M
Table of Contents
Hook-up With Floating Top Links
1. Complete steps 1 thru 7 on this page except shorten
top center link to keep upper hook from capturing
implement's upper hitch point.
2. Attach floating top links to Quick Hitch and
implement. Refer to "Floating Top Link" on page 15
for detailed instructions.
QH15 Spare Bushings
Additional bushings may be purchased from your local
Land Pride dealer to make more than one implement
readily available for quick hook-up. If implement has
single lower hitch pins, bushing kit #320-034A is
recommended. See Figure 1-6 on page 11 for single hitch
pin application.
Part No.
320-034A
320-048D
320-044D
320-045D
320-050D
320-051D
325-017D
320-052D
QH20 Spare Bushings
Additional bushings may be purchased from your local
Land Pride dealer so that more than one implement is
readily available for quick hook-up.
Part No.
890-938C
890-939C
890-940C
890-941C
Auto-Lock Hooks
Implement Hook-Up
Figure 1-5
QH15 Lower Bushings
Part Description
2- Stepped Bushings CAT. l to CAT. lll Adapter
Spacer Tube 1.44" O.D. x .91" I.D. x 1 9/32" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 1 1/2" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 1 15/16" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 2 3/16" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 2 7/16" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 2 7/8" lg.
Spacer Tube 1.44" O.D. x .93" I.D. x 3 1/2" lg.
QH20 Lower Bushings
Part Description
Stepped Bushing CAT. ll to CAT. lll Adapter
Spacer Tube 1.44" O.D. x 1.14" I.D. x 1 3/4" lg.
Spacer Tube 1.44" O.D. x 1.14" I.D. x 2 1/2" lg.
Spacer Tube 1.44" O.D. x 1.14" I.D. x 2 3/4" lg.
Standard Cat. l Configuration
Connect Upper Hook to the Lower Center
Hitch Pin/Bolt (Upper HItch Point)
17293
12/04/15